Lenovo PC 300PL About Your Software - Windows 95 Application and Support Softw - Page 39

Microsoft Windows 95, CD-ROM, Setup Boot Disk, Ready-to-Con Utility Program

Get Lenovo PC 300PL PDF manuals and user guides View all Lenovo PC 300PL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

h. Verify that the Microsoft Windows 95 CD is in the CD-ROM drive, and press Y to continue. Note: If you open the CD-ROM drive in this step, after you close the drive, you must wait for the drive to recognize that there is a CD in the drive before you press Y. If the message CDR1 1: Not ready reading drive X is displayed, press R (Retry) until the drive recognizes the CD. i. Click on Continue. In each of the Windows 95 Setup windows, make your selection or type the requested information, and follow the prompts. Accept the Microsoft license agreement, and type the Product ID number from the Microsoft Certificate of Authenticity when you are prompted to do so. (The Certificate of Authenticity is attached to the front cover of your Windows 95 manual.) j. When you are prompted to do so, remove the CD-ROM Setup Boot Disk from drive A; click on Finish to restart the computer and begin the hardware setup. Follow the prompts to complete the hardware setup. k. When the hardware setup is completed, click on OK to restart Windows 95. l. A Windows 95 Setup screen appears. If you want to install Internet Explorer 4.0x and its active desktop, click on Next. If you do not want to install Internet Explorer 4.0x, click on the Windows Start button. Then click on Shutdown, Restart the Computer, and Yes. m. Remove the CD from the CD-ROM drive. n. If necessary, install relevant device drivers or other software from the Ready-to-Configure Utility Program CD. (See Chapter 5, "Using the Ready-to-Configure Utility Program CD" on page 37 for additional information.) For a list of devices for which device drivers were not installed, click on the Windows Start button. Then click on Settings and Control Panel. On the Control Panel, click on System and the Device Manager tab. Then click on the + symbol next Chapter 4. Reinstalling Windows 95 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
h.
Verify that the
Microsoft Windows 95
CD is in the CD-ROM
drive, and press
Y
to continue.
Note:
If you open the CD-ROM drive in this step, after you
close the drive, you must wait for the drive to
recognize that there is a CD in the drive before you
press
Y.
If the message
CDR1²1: Not ready reading drive X
is displayed, press
R
(Retry) until the drive
recognizes the CD.
i.
Click on
Continue
.
In each of the Windows 95 Setup
windows, make your selection or type the requested
information, and follow the prompts.
Accept the Microsoft
license agreement, and type the Product ID number from
the Microsoft Certificate of Authenticity when you are
prompted to do so.
(The Certificate of Authenticity is
attached to the front cover of your Windows 95 manual.)
j.
When you are prompted to do so, remove the
CD-ROM
Setup Boot Disk
from drive A; click on
Finish
to restart the
computer and begin the hardware setup.
Follow the
prompts to complete the hardware setup.
k.
When the hardware setup is completed, click on
OK
to
restart Windows 95.
l.
A Windows 95 Setup screen appears.
If you want to install
Internet Explorer 4.0x and its active desktop, click on
Next
.
If you do not want to install Internet Explorer 4.0x, click on
the Windows
Start
button.
Then click on
Shutdown
,
Restart the Computer
, and
Yes
.
m.
Remove the CD from the CD-ROM drive.
n.
If necessary, install relevant device drivers or other software
from the
Ready-to-Configure Utility Program
CD.
(See
Chapter
5, “Using the Ready-to-Configure Utility Program
CD” on page
37 for additional information.)
For a list of
devices for which device drivers were not installed, click on
the Windows
Start
button.
Then click on
Settings
and
Control Panel
.
On the Control Panel, click on
System
and
the
Device Manager
tab.
Then click on the
+
symbol next
Chapter 4.
Reinstalling Windows 95
31