Lenovo PC 300PL About Your Software - Windows 95 Application and Support Softw - Page 45

Using the Ready-to-Con Utility Program CD, Features of the CD

Page 45 highlights

Chapter 5. Using the Ready-to-Configure Utility Program CD Use the information in this chapter if you want to install or reinstall device drivers and other software from the Ready-to-Configure Utility Program CD. Features of the CD The Ready-to-Configure Utility Program CD contains device drivers, diagnostic programs, and other support software for a variety of operating system environments. Important The Ready-to-Configure Utility Program CD does not contain operating systems. Before you can use the CD, your operating system must already be installed on your computer. You can use the CD to: Install some products directly from the CD on models equipped with a CD-ROM drive. Create a local area network (LAN) image of the software products on the Ready-to-Configure Utility Program CD and install the products from a LAN disk. Create diskettes for software products that cannot be installed from the CD and install the products from diskette. The utility program on the CD has an easy-to-use, graphical interface and automated installation procedures for most products. The utility program also has a help system and a comprehensive overview that describes the features of the utility program, the software products that can be installed from the CD, and the operating environments that are supported by those products. The products on the Ready-to-Configure Utility Program CD are licensed according to the terms and conditions of the IBM International Program License Agreement and the License Information contained in the CD overview. The license information in Appendix A of this booklet is for the preinstalled software; the license information in the CD overview is for the CD software. © Copyright IBM Corp. 1998 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58

Chapter 5.
Using the Ready-to-Configure Utility Program CD
Use the information in this chapter if you want to install or reinstall
device drivers and other software from the
Ready-to-Configure Utility
Program
CD.
Features of the CD
The
Ready-to-Configure Utility Program
CD contains device drivers,
diagnostic programs, and other support software for a variety of
operating system environments.
Important
The
Ready-to-Configure Utility Program
CD does not contain
operating systems.
Before you can use the CD, your operating
system must already be installed on your computer.
You can use the CD to:
±
Install some products directly from the CD on models equipped
with a CD-ROM drive.
±
Create a local area network (LAN) image of the software
products on the
Ready-to-Configure Utility Program
CD and install
the products from a LAN disk.
±
Create diskettes for software products that cannot be installed
from the CD and install the products from diskette.
The utility program on the CD has an easy-to-use, graphical
interface and automated installation procedures for most products.
The utility program also has a help system and a comprehensive
overview that describes the features of the utility program, the
software products that can be installed from the CD, and the
operating environments that are supported by those products.
The products on the
Ready-to-Configure Utility Program
CD are
licensed according to the terms and conditions of the IBM
International Program License Agreement and the License
Information contained in the CD overview.
The license information
in Appendix
A of this booklet is for the preinstalled software; the
license information in the CD overview is for the CD software.
Copyright IBM Corp. 1998
37