Lenovo ThinkCentre M60e Hardware Maintenance Manual for ThinkCentre M60e - Page 99

Replacing the system board

Get Lenovo ThinkCentre M60e PDF manuals and user guides View all Lenovo ThinkCentre M60e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

6. Slide the new hard disk drive into the hard disk drive bay and align the screw holes in the new hard disk drive with the corresponding holes in the drive bay. Then, install the four screws to secure the new hard disk drive in place. Figure 25. Installing the hard disk drive 7. Connect one end of the signal cable to the rear of the new hard disk drive and the other end to an available SATA connector on the system board. See "Locating parts on the system board" on page 76. Then, locate an available five-wire power connector and connect it to the rear of the new hard disk drive. Figure 26. Connecting a SATA hard disk drive 8. To complete the installation or replacement, go to "Completing the parts replacement" on page 99. Replacing the system board Attention: Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the ThinkCentre User Guide. To obtain a copy of the ThinkCentre User Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the system board. Chapter 8. Replacing FRUs (Machine Types: 1899, 1928, 1932, and 1934) 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
6. Slide the new hard disk drive into the hard disk drive bay and align the screw holes in the new hard
disk drive with the corresponding holes in the drive bay. Then, install the four screws to secure the
new hard disk drive in place.
Figure 25. Installing the hard disk drive
7. Connect one end of the signal cable to the rear of the new hard disk drive and the other end to an
available SATA connector on the system board. See “Locating parts on the system board” on page 76.
Then, locate an available five-wire power connector and connect it to the rear of the new hard disk drive.
Figure26. Connecting a SATA hard disk drive
8. To complete the installation or replacement, go to “Completing the parts replacement” on page 99.
Replacing the system board
Attention:
Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the
ThinkCentre User Guide
. To obtain a copy of the
ThinkCentre User Guide
, go to:
This section provides instructions on how to replace the system board.
Chapter 8
.
Replacing FRUs (Machine Types: 1899, 1928, 1932, and 1934)
95