Lenovo ThinkCentre Tiny-in-One 23 User Guide (English) - Page 9

Setting up your monitor - optical drive

Page 9 highlights

Setting up your monitor This section provides the following information: ● Assembling your monitor ● Connecting cables ● Turning on your monitor and computer Note: Before setting up your monitor, ensure that you have read and understood the "Safety information" on page iii. Assembling your monitor To assemble your monitor, follow the five parts below one by one: Part 1: Install the full-function monitor stand. Part 2: Install the Tiny. Part 3: Install the rear Wi-Fi antenna. Part 4: Install the optical drive. Part 5: Install the Kensington-style cable lock. Note: The rear Wi-Fi antenna, the optical drive, and the Kensington-style cable lock are available only on some models. Part 1: Install the full-function monitor stand. Note: The full-function monitor stand includes the stand that has been installed on the monitor and the base that comes with the monitor. 1. Place a soft, clean towel or cloth on the desk or surface. Hold the sides of your monitor and gently lay it down so that the screen is against the surface and the cover is facing up. 2. Insert the two metal studs into the corresponding holes in the stand. Then, tighten the screw that is embedded in the base. Place the monitor in an upright position. Part 2: Install the Tiny. 1. Gently hold the cable cover 1 and slide the latch to the right to open the cable cover. Then, push the decorative cover 2 upward to remove the decorative cover. Note: Keep the decorative cover for future use. 4 ThinkCentre Tiny-in-One 23 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45

Setting up your monitor
This section provides the following information:
Assembling your monitor
Connecting cables
Turning on your monitor and computer
Note: Before setting up your monitor, ensure that you have read and understood the “Safety information” on page iii.
Assembling your monitor
To assemble your monitor, follow the five parts below one by one:
Part 1: Install the full-function monitor stand.
Part 2: Install the
T
iny.
Part 3: Install the rear Wi-Fi antenna.
Part 4: Install the optical drive.
Part 5: Install the Kensington-style cable lock.
Note: The rear Wi-Fi antenna, the optical drive, and the Kensington-style cable lock are available only on some
models.
Part 1: Install the full-function monitor stand.
Note: The full-function monitor stand includes the stand that has been installed on the monitor and the base that
comes with the monitor.
1. Place a soft, clean towel or cloth on the desk or surface. Hold the sides of your monitor and gently lay it
down so that the screen is against the surface and the cover is facing up.
2. Insert the two metal studs into the corresponding holes in the stand. Then, tighten the screw that is
embedded in the base. Place the monitor in an upright position.
Part 2: Install the
Tiny
.
1. Gently hold the cable cover 1 and slide the latch to the right to open the cable cover. Then, push the decorative cover
2 upward to remove the decorative cover.
Note: Keep the decorative cover for future use.
4
ThinkCentre Tiny-in-One 23 User Guide