LevelOne FCS-4041 User Manual - Page 66

Auto Pan

Get LevelOne FCS-4041 PDF manuals and user guides View all LevelOne FCS-4041 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Cruise Run Select the specified Cruise Path from the drop-down list, click on the button, and then the camera will start touring around as recorded. To view the camera touring around in full screen mode, please move the cursor onto the live view pane, right-click and left-click to select "fullscreen". Then users can view the camera navigation in full screen. To stop running a Cruise Path, simply move the cursor to the live view pane and move the camera in any direction. 7.4.3 Auto Pan The Auto Pan Programming can be found under this path: PTZ> Auto Pan. The IP Camera supports four Auto Pan Paths. Please refer to the instructions below to set an Auto Pan Path. Auto Pan Setting To setup an Auto Pan Path, please select a path number from the drop-down list first. Then move the cursor to the live view pane, and move the camera to a desired view as the Start Point of an Auto Pan Path. Click on the button of the and the current view will be automatically saved as the start point of the Auto Pan Path. NOTE: The room ratio of an Auto Pan's Start Point will persist throughout the whole path. Enter the speed ratio into the Speed field; the speed ratio ranges from 0 (low) to 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
66
Cruise Run
Select the specified Cruise Path from the drop-down list, click on the <Run>
button, and then the camera will start touring around as recorded.
To view the camera touring around in full screen mode, please move the cursor
onto the live view pane, right-click and left-click to select
“fu
l
lscreen”.
Then
users can view the camera navigation in full screen.
To stop running a Cruise Path, simply move the cursor to the live view pane and
move the camera in any direction.
7.4.3
Auto Pan
The Auto Pan Programming can be found under this path:
PTZ> Auto Pan
.
The IP Camera supports four Auto Pan Paths. Please refer to the instructions
below to set an Auto Pan Path.
Auto Pan Setting
To setup an Auto Pan Path, please select a path number from the drop-down list
first. Then move the cursor to the live view pane, and move the camera to a
desired view as the Start Point of an Auto Pan Path. Click on the <Set> button of
the <Start Point> and the current view will be automatically saved as the start
point of the Auto Pan Path.
NOTE:
The room ratio of an Auto Pa
n’
s Start Point will persist
throughout the whole path.
Enter the speed ratio into the Speed field; the speed ratio ranges from 0 (low) to