LevelOne WAC-1000 User Manual - Page 47

Configuration steps, Settings, Service area, Device

Get LevelOne WAC-1000 PDF manuals and user guides View all LevelOne WAC-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Figure 9- 14 AP centralized management configuration instance Configuration steps: 1) Access configuration Connect the WAC - 1000 / WAC - 1000 in bypass mode of the company network, here, the upper interface VLAN connected to WAC-1000 / WAC-1001 is VLAN10. 2) Interface configuration Log in to WAC-1000 / WAC-1001, to configure the LAN port, WAN port of the device, to complete the basic configuration on the Internet. Here, the LAN port IP address is 192.168.1.252. 3) Service area configuration Enter the Settings→Service area page, to configure service area as default, S2. The SSID of Service area default is set to HiPER_IN, enable SSID broadcasting, the encryption mode is set to WPA-PSK/WPA2-PSK, the pre-shared key is 1234567890, and the AP management VLAN range is set to 10. The configuration of Service area S2 is shown in the figure below, SSID is set to HiPER_OUT, the SSID broadcasting is enabled, and the encryption mode is WPA-PSK/WPA2-PSK, and the AP management VLAN range is set to 10. Figure 9- 15 Service area configuration 4) Remote management After the DHCP server, service area, etc. are configured, you can enter the Device page, and click on the top of page, and remotely manage the three APs after the corresponding APs are shown respectively. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
43
Figure 9- 14 AP centralized management configuration instance
Configuration steps:
1) Access configuration
Connect the WAC - 1000 / WAC
–
1000 in bypass mode of the company network, here, the upper interface
VLAN connected to WAC-1000 / WAC-1001 is VLAN10.
2) Interface configuration
Log in to WAC-1000 / WAC-1001, to configure the LAN port, WAN port of the device, to complete the basic
configuration on the Internet. Here, the LAN port IP address is 192.168.1.252.
3) Service area configuration
Enter the
Settings
→
Service area
page, to configure service area as default, S2.
The SSID of Service area default is set to HiPER_IN, enable SSID broadcasting, the encryption mode is set to
WPA-PSK/WPA2-PSK, the pre-shared key is 1234567890, and the AP management VLAN range is set to 10.
The configuration of Service area S2 is shown in the figure below, SSID is set to HiPER_OUT, the SSID
broadcasting is enabled, and the encryption mode is WPA-PSK/WPA2-PSK, and the AP management VLAN
range is set to 10.
Figure 9- 15 Service area configuration
4) Remote management
After the DHCP server, service area, etc. are configured, you can enter the
Device
page, and click on the top
of page, and remotely manage the three APs after the corresponding APs are shown respectively.