LevelOne WAC-1000 User Manual - Page 48

AP centralized management configuration instance Three, layer management

Get LevelOne WAC-1000 PDF manuals and user guides View all LevelOne WAC-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

In the remote management page, click on the AP name → Settings → Service settings. After entering the service area list page, check the service areas whose names are default, S2, and then click the Join service button. Add other two APs into these two service areas in the same way. 5) AP load balancing Enter the Settings → Load balancing page, click the Add button, to enter the load balancing group configuration interface, and check Enable load balancing group, and input the name of load balancing group, HiPER_NEW, add three APs into the load balancing group, and click Save. With the above configuration, the enterprise employees can access to the network through HiPER_IN; the outsiders can access to the network through HiPER_OUT. 9.6 AP centralized management configuration instance (Three layer management) 9.6.1 Typical environment I (option43/ option60 for the application of the ACCESS port and 3 layer switches) 1) Demand: Analyze the WAC-1000 / WAC-1001 address in the AP through the option43 field, and discover AC by three layers. VLAN is divided into three parts on the 3-layer switch, VLAN1, VLAN2, VLAN3 respectively, and WAP-6201 is on the access interface to which VLAN2 of the 3-layer switch, and the IP address for VLAN2 virtual interface is 192.168.2.254. WAP-6111 is on the access interface to which VLAN3 of the 3-layer switch, and the IP address for VLAN3 virtual interface is 192.168.3.254. The IP address of AC LAN is 192.168.1.252, and the IP for VLAN1 virtual interface is 192.168.1.254. The pool of the corresponding VLAN is created for the virtual interface in the VLANs, and the IP address of option43 with the field of WAC-1000 /WAC-1001 is defined. The dotted decimal format is 192.168.1.252; the dotted hexadecimal format is 0104C0A801FC, here, 01 represents fixed identifier while 04 represents the character length of 4 bytes. And configure the option60 field format as ASCII, and the character content as LEVELONE, this is AP supported field. 2） Environment topology 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
44
In the remote management page, click on the AP name
→
Settings
→
Service settings
. After entering the
service area list page, check the service areas whose names are default, S2, and then click the
Join service
button.
Add other two APs into these two service areas in the same way.
5) AP load balancing
Enter the
Settings
→
Load balancing
page, click the
Add
button, to enter the load balancing group
configuration interface, and check Enable load balancing group, and input the name of load balancing group,
HiPER_NEW, add three APs into the load balancing group, and click
Save
.
With the above configuration, the enterprise employees can access to the network through HiPER_IN; the
outsiders can access to the network through HiPER_OUT.
9.6 AP centralized management configuration instance (Three
layer management)
9.6.1 Typical environment I (option43/ option60 for the application of the
ACCESS port and 3 layer switches)
1) Demand:
Analyze the WAC-1000 / WAC-1001 address in the AP through the option43 field, and discover AC by three
layers.
VLAN is divided into three parts on the 3-layer switch, VLAN1, VLAN2, VLAN3 respectively, and WAP-6201
is on the access interface to which VLAN2 of the 3-layer switch, and the IP address for VLAN2 virtual interface
is 192.168.2.254. WAP-6111 is on the access interface to which VLAN3 of the 3-layer switch, and the IP address
for VLAN3 virtual interface is 192.168.3.254. The IP address of AC LAN is 192.168.1.252, and the IP for
VLAN1 virtual interface is 192.168.1.254. The pool of the corresponding VLAN is created for the virtual
interface in the VLANs, and the IP address of option43 with the field of WAC-1000 /WAC-1001 is defined. The
dotted decimal format is 192.168.1.252; the dotted hexadecimal format is 0104C0A801FC, here, 01 represents
fixed identifier while 04 represents the character length of 4 bytes. And configure the option60 field format as
ASCII, and the character content as LEVELONE, this is AP supported field.
2
）
Environment topology