Lexmark Optra C710 Setup Guide - Page 103

AppleTalk - firmware

Get Lexmark Optra C710 PDF manuals and user guides View all Lexmark Optra C710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

7 See if the network printer shows up in MarkVision. - If it doesn't, the print server may have downlevel firmware. - If it does but you still cannot print, try removing then re-adding the Lexmark Network Port on the printer object. 8 Reset both the print server and the printer. 9 If possible, shut down Windows NT Server and restart the server. There could be a spooler problem that requires a restart. 10 Uninstall, then reinstall MarkVision. During the reinstallation, select only the network protocols you actually use (for example, TCP/IP). This also helps MarkVision run faster. 11 Try printing again. 12 If you are still having trouble, contact Lexmark for help at 1-800-LEXMARK (1-800-539-6275) or on the World Wide Web at http://www.lexmark.com. AppleTalk 1 Make sure the AppleTalk protocol is turned on (activated) in the print server. To find out, print a network setup page and look in the paragraph under AppleTalk. 2 Look at the network setup page again and notice the AppleTalk name and the AppleTalk zone for the printer. 3 Make sure you are looking at the correct zone in the Macintosh Chooser. The zone must be the same one as listed on the setup page. AppleTalk 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
99
AppleTalk
7
See if the network printer shows up in
MarkVision.
–
If it doesn’t, the print server may have down-
level firmware.
–
If it does but you still cannot print, try removing
then re-adding the Lexmark Network Port on the
printer object.
8
Reset both the print server and the printer.
9
If possible, shut down Windows NT Server and
restart the server. There could be a spooler
problem that requires a restart.
10
Uninstall, then reinstall MarkVision. During the
reinstallation, select only the network protocols
you actually use (for example, TCP/IP). This also
helps MarkVision run faster.
11
Try printing again.
12
If you are still having trouble, contact Lexmark for
help at 1-800-LEXMARK (1-800-539-6275) or on the
World Wide Web at http://www.lexmark.com.
AppleTalk
1
Make sure the AppleTalk protocol is turned on
(activated) in the print server. To find out, print a
network setup page and look in the paragraph
under AppleTalk.
2
Look at the network setup page again and notice
the AppleTalk name and the AppleTalk zone for
the printer.
3
Make sure you are looking at the correct zone in
the Macintosh Chooser. The zone must be the
same one as listed on the setup page.