Lexmark Optra E plus User's Guide - Page 27

Installing memory, Removing the, system board shield

Get Lexmark Optra E plus PDF manuals and user guides View all Lexmark Optra E plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installing memory To install a memory card or a flash memory card, go on to the next section. Otherwise, you are ready to set up your application software and install the appropriate printer driver. Refer to the booklet that came with the Drivers, MarkVision and Utilities CD for installation instructions. Go to Printer drivers for more information about the printer utilities and drivers. Your printer comes with 4MB of printer memory. You can buy and install a 4MB, 8MB, 16MB, 32MB or 64MB optional memory card for a total of 68MB of printer memory. You can also install a 1MB, 2MB or 4MB optional flash memory card for storing downloaded fonts or macros. Removing the system board shield Before installing any of these option cards, you will need a small Phillips screwdriver to remove the metal shield covering the printer system board. 1 Turn off the printer and unplug the power cord from the printer. 2 Disconnect the printer cable (if attached) from the printer. 3 Remove the print cartridge and cover it. 14 Chapter 1: The basics

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
14
Chapter 1: The basics
Installing memory
To install a memory card or a flash memory card, go on
to the next section. Otherwise, you are ready to set up
your application software and install the appropriate
printer driver. Refer to the booklet that came with the
Drivers, MarkVision and Utilities
CD for installation
instructions. Go to
Printer drivers
for more information
about the printer utilities and drivers.
Your printer comes with 4MB of printer memory. You
can buy and install a 4MB, 8MB, 16MB, 32MB or 64MB
optional memory card for a total of 68MB of printer
memory.
You can also install a 1MB, 2MB or 4MB optional flash
memory card for storing downloaded fonts or macros.
Removing the
system board shield
Before installing any of these option cards, you
will
need a small Phillips screwdriver to
remove the metal
shield covering the printer system board.
1
Turn off the printer and unplug the power cord
from the printer.
2
Disconnect the printer cable (if attached) from
the printer.
3
Remove the print cartridge and cover it.