Lexmark X782e IPDS Printer and Host Setup Guide - Page 50

Printer and Host Timeout Values

Get Lexmark X782e PDF manuals and user guides View all Lexmark X782e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

IPDS Printer and Host Setup Guide Printer and Host Timeout Values 7. Printer and Host Timeout Values Selecting compatible values of the printer IPDS Timeout value and host release timers is very important when printing IPDS jobs. Selection of some values will cause communication problems between the printer and the host. Use the tables below to verify the timeout settings in the printer and on the host. AS/400 or iSeries and Printer Timeout Values Printer IPDS Timeout Host Controlled 15 sec to 10 Min AS/400 or iSeries Release AS/400 or iSeries Device Description Note Timer Valid Port Number *SEC15 5001, 9100, 9600 *SEC30 5001, 9100, 9600 Specific Number of Seconds 5001, 9100, 9600 1 *NOMAX None 2 *SEC15 5001, 9600 3 *SEC30 5001, 9600 3 Specific Number of Seconds 5001, 9600 3 *NOMAX 5001, 9600 4 Note 1: The number of seconds should be greater than or equal to 15 seconds. Note 2: The Release Timer and IPDS Timeout value are not compatible. The printer will remain busy after the IPDS job has completed. Jobs from other IPDS sessions and non-IPDS jobs waiting on other ports will not print. Note 3: These Release Timer values are not recommended when the IPDS Timeout is set to a specific value. If used, the difference between the two timers should be a minimum of 30 seconds. Note 4: An IPDS Timeout value of 15 sec or 30 sec is recommended. This allows 15 or 30 seconds for the host to send another job before the printer times out and starts printing jobs waiting on other ports. MVS and Printer Timeout Values - see next page 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
50
IPDS Printer and Host Setup Guide
Printer and Host Timeout Values
7.
Printer and Host Timeout Values
Selecting compatible values of the printer IPDS Timeout value and host release timers is very important when
printing IPDS jobs.
Selection of some values will cause communication problems between the printer and the
host.
Use the tables below to verify the timeout settings in the printer and on the host.
AS/400 or iSeries and Printer Timeout Values
Note 1:
The number of seconds should be greater than or equal to 15 seconds.
Note 2:
The Release Timer and IPDS Timeout value are not compatible.
The printer will remain busy after the
IPDS job has completed.
Jobs from other IPDS sessions and non-IPDS jobs waiting on other ports
will not print.
Note 3:
These Release Timer values are not recommended when the IPDS Timeout is set to a specific value.
If used, the difference between the two timers should be a minimum of 30 seconds.
Note 4:
An IPDS Timeout value of 15 sec or 30 sec is recommended.
This allows 15 or 30 seconds for the
host to send another job before the printer times out and starts printing jobs waiting on other ports.
MVS and Printer Timeout Values - see next page
Printer IPDS
Timeout
AS/400 or iSeries Release
Timer
AS/400 or iSeries Device Description
Valid Port Number
Note
Host Controlled
*SEC15
5001, 9100, 9600
*SEC30
5001, 9100, 9600
Specific Number of Seconds
5001, 9100, 9600
1
*NOMAX
None
2
15 sec to 10 Min
*SEC15
5001, 9600
3
*SEC30
5001, 9600
3
Specific Number of Seconds
5001, 9600
3
*NOMAX
5001, 9600
4