Lexmark X782e IPDS Printer and Host Setup Guide - Page 56

PSF/MVS, PSF/2, PSF/AIX, PSF/400 with OS/400 V3R1 or V3R6, V3R7, V4R1-R5, or V5R1-R4, or greater

Get Lexmark X782e PDF manuals and user guides View all Lexmark X782e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

IPDS Printer and Host Setup Guide Printer Messages and Problems PSF/MVS PSF Startup Proc: Disconnect Interval (DISCINTV) PSF/2 TCP/IP Settings: Connect Timeout Tuning Option: Job Interval Shutdown Timer PSF/AIX SMIT Printer Def: Connect Timeout 15 seconds 30 seconds 30 seconds 30 seconds IPDS Timeout = 15 seconds to 10 minutes (when using the Standard Network port or a MarkNet internal LAN print server) Note: The printer defaults to Host Controlled when receiving IPDS jobs on port 9100. If you selected the IPDS Timeout value of Host Controlled in order to allow the host to directly control ending (disconnecting) a LAN session, go to IPDS Timeout = Host Controlled above (page 55). If you selected an IPDS Timeout value of 15 seconds to 10 minutes in order to allow the printer IPDS emulation to determine when an IPDS LAN session times out, follow the steps below to correct the problem. 1 Disable the printer's Network Job Timeout by setting it to 0. For instructions on how to do this, see the "Configure the Printer's Network Job Timeout" step in the chapter in this guide that describes your host environment. 2 Change the host port setting to 5001 or 9600. Refer to "Printer and Host Timeout Values" [page 50] for valid values. Additional information on the IPDS Timeout and port settings may be found in the IPDS Emulation User's Guide. 3 After changing the host port setting to 5001 or 9600, correct the appropriate host timer/timeout value as shown below. Note: The host timer/timeout values below should not be used with a host port value of 9100. PSF/400 with OS/400 V3R1 or V3R6 WRKAFP2: Inactivity Timer (INACTTMR) PSF/400 with OS/400 V3R2, V3R7, V4R1-R5, or V5R1-R4 or greater CRTPSFCFG: Release Timer (RLSTMR) PSF/MVS PSF Startup Proc: Disconnect Interval (DISCINTV) PSF/2 TCP/IP Settings: Connect Timeout Tuning Option: Job Interval Shutdown Timer PSF/AIX SMIT Printer Def: Connect Timeout *NOMAX *NOMAX 0 0 9999 0 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
56
IPDS Printer and Host Setup Guide
Printer Messages and Problems
IPDS Timeout = 15 seconds to 10 minutes
(when using the Standard Network port or a MarkNet internal LAN print server)
Note:
The printer defaults to
Host Controlled
when receiving IPDS jobs on port 9100.
If you selected the
IPDS Timeout
value of
Host Controlled
in order to allow the host to directly control ending
(disconnecting) a LAN session, go to
IPDS Timeout = Host Controlled
above (page
55
).
If you selected an
IPDS Timeou
t value of
15 seconds to 10 minutes
in order to allow the printer IPDS emula-
tion to determine when an IPDS LAN session times out, follow the steps below to correct the problem.
1
Disable the printer’s
Network Job Timeout
by setting it to 0. For instructions on how to do this, see the
"Configure the Printer’s Network Job Timeout" step in the chapter in this guide that describes your host
environment.
2
Change the
host port setting
to 5001 or 9600. Refer to
“Printer and Host Timeout Values” [page 50]
for valid
values. Additional information on the
IPDS Timeout
and port settings may be found in the IPDS Emulation
User’s Guide.
3
After changing the host port setting to 5001 or 9600, correct the appropriate
host timer/timeout
value as
shown below.
Note:
The
host timer/timeout
values below should
not
be used with a host port value of 9100.
PSF/MVS
PSF Startup Proc: Disconnect Interval (DISCINTV)
15 seconds
PSF/2
TCP/IP Settings: Connect Timeout
Tuning Option: Job Interval Shutdown Timer
30 seconds
30 seconds
PSF/AIX
SMIT Printer Def: Connect Timeout
30 seconds
PSF/400 with OS/400 V3R1 or V3R6
WRKAFP2: Inactivity Timer (INACTTMR)
*NOMAX
PSF/400 with OS/400 V3R2, V3R7, V4R1-R5, or V5R1-R4
or greater
CRTPSFCFG: Release Timer (RLSTMR)
*NOMAX
PSF/MVS
PSF Startup Proc: Disconnect Interval (DISCINTV)
0
PSF/2
TCP/IP Settings: Connect Timeout
Tuning Option: Job Interval Shutdown Timer
0
9999
PSF/AIX
SMIT Printer Def: Connect Timeout
0