LiftMaster EL1SS EL1SS Installation and Programming Manual - Page 17

Code Setup, Code Operation, Enter A Temporary 1 Shot User Code Number

Get LiftMaster EL1SS PDF manuals and user guides View all LiftMaster EL1SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

INTRODUCTION INSTALLATION TESTING PROGRAMMING ADJUST RELAY OUTPUT TIME (RELAY 2) The amount of time (in seconds) the relay remains active. Default level is 0.5 seconds. 1. Enter the Master Code: ? ? ? ? 2. Enter the Program Code: 0 2 5 3. Enter the Output Time (in seconds): ? ? ? ? Example: 0000 = 0.5 Seconds (Minimum) 0010 = 10 Seconds 8000 = 8000 Seconds (2 hours & 13 minutes, Maximum) CODE SETUP The unit's Master Code is for owner/administrator level commands. The User Codes allow users to activate and latch relays 1 and 2 and to transmit radio commands on channels one and two. NOTE: The User Code cannot be the same as the Master Code. DISABLE VACATION (LOCK DOWN) MODE 1. Enter the Master Code: ? ? ? ? 2. Enter the Program Code: 5 3 TRIGGER RELAY 1 AND CHANNEL 1 1. Enter the Master Code: ? ? ? ? 2. Enter the Program Code: 1 TRIGGER RELAY 2 AND CHANNEL 2 1. Enter the Master Code: ? ? ? ? 2. Enter the Program Code: 2 ENTER A USER CODE NUMBERS 1. Enter the Master Code: ? ? ? ? The unit will beep. 2. Enter the Program Code: 9 The unit will beep. 3. Enter New User Code: 4. Enter the Relay/Channel for the Code to control: 1 or 2 or no button is pressed. NOTE: If no button is pressed in step 4, both relays/channels will activate simultaneously, when in parallel mode. CODE OPERATION MASTER CODE OPERATIONS TRIGGER RELAY 1 (ONLY) Enter the Master Code: ? ? ? ? NOTE: Requires Relay 2 be in Independent Mode. ENABLE VACATION (LOCK DOWN) MODE Locks the system from all User Code activity. 1. Enter the Master Code: ? ? ? ? 2. Enter the Program Code: 5 2 USER CODE OPERATIONS TRIGGER PROGRAMMED RELAY/CHANNEL FOR USER CODE Enter the User Code: ? ? ? ? The appropriate Relay/Channel will activate. DELETE USER CODE NUMBERS 1. Enter the Master Code: ? ? ? ? The unit will beep. 2. Enter the Program Code: 7 The unit will beep. 3. Enter User Code to be deleted: ENTER A TEMPORARY (1 SHOT) USER CODE NUMBER The EL1SS holds 1 temporary User Code. 1. Enter the Master Code: ? ? ? ? 2. Enter the Program Code: 5 1 The unit will beep. 3. Enter the Temporary User Code: 4. Enter the Relay for the Code to control: 1 or 2 or no button is pressed. NOTE: If no button is pressed in step 4, both relays will activate simultaneously. Expires in 24 hours or after first use. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
15
INTRODUCTION
PROGRAMMING
TESTING
INSTALLATION
TRIGGER RELAY 1 (ONLY)
Enter the Master Code:
?
?
?
?
NOTE:
Requires Relay 2 be in Independent Mode.
ENABLE VACATION (LOCK DOWN) MODE
Locks the system from all User Code activity.
1.
Enter the Master Code:
?
?
?
?
2. Enter the Program Code:
5
2
DISABLE VACATION (LOCK DOWN) MODE
1.
Enter the Master Code:
?
?
?
?
2. Enter the Program Code:
5
3
TRIGGER RELAY 1 AND CHANNEL 1
1.
Enter the Master Code:
?
?
?
?
2. Enter the Program Code:
1
TRIGGER RELAY 2 AND CHANNEL 2
1.
Enter the Master Code:
?
?
?
?
2. Enter the Program Code:
2
The unit’s Master Code is for owner/administrator level
commands. The User Codes allow users to activate and latch
relays 1 and 2 and to transmit radio commands on channels one
and two.
NOTE:
The User Code cannot be the same as the Master Code.
CODE SETUP
CODE OPERATION
MASTER CODE OPERATIONS
TRIGGER PROGRAMMED RELAY/CHANNEL FOR USER CODE
Enter the User Code:
?
?
?
?
The appropriate
Relay/Channel will activate.
USER CODE OPERATIONS
ENTER A TEMPORARY (1 SHOT) USER CODE NUMBER
The EL1SS holds 1 temporary User Code.
1.
Enter the Master Code:
?
?
?
?
2.
Enter the Program Code:
5
1
The unit will beep.
3. Enter the Temporary User Code:
4.
Enter the Relay for the Code to control:
1
or
2
or no
button is pressed.
NOTE:
If no button is pressed in step 4, both relays will
activate simultaneously. Expires in 24 hours or after
first use.
ENTER A USER CODE NUMBERS
1. Enter the Master Code:
?
?
?
?
The unit will
beep.
2. Enter the Program Code:
9
The unit will beep.
3. Enter New User Code:
4. Enter the Relay/Channel for the Code to control:
1
or
2
or no button is pressed.
NOTE:
If no button is pressed in step 4, both
relays/channels will activate simultaneously, when in
parallel mode.
DELETE USER CODE NUMBERS
1.
Enter the Master Code:
?
?
?
?
The unit will
beep.
2.
Enter the Program Code:
7
The unit will beep.
3.
Enter User Code to be deleted:
ADJUST RELAY OUTPUT TIME (RELAY 2)
The amount of time (in seconds) the relay remains active.
Default level is 0.5 seconds.
1. Enter the Master Code:
?
?
?
?
2. Enter the Program Code:
0
2
5
3.
Enter the Output Time (in seconds):
?
?
?
?
Example:
0000 = 0.5 Seconds (Minimum)
0010 = 10 Seconds
8000 = 8000 Seconds (2 hours & 13 minutes, Maximum)