Maytag MED6600TQ Use and Care Guide - Page 27

•

•

o

You can

change

Sensor

Dry

and

Timed

Cycles,

Modifiers

and Options

anytime

before

pressing

Start.

•

Three short

tones

sound

if an unavailable

combination

is selected.

The last selection

will

not

be accepted.

Changing

Cycles

after

pressing

Start

1.

Press PAUSE/CANCEl

twice.

2.

Select

the desired

cycle

and

options.

3.

Press STARL

[-he dryer

starts

at the beginning

of the

new

cycle.

NOTE:

If you do

not

press Start within

5 minutes

of selecting

the

cycle,

the

dryer

automatically

shuts

off.

Changing

Modifiers

and

Options

after

pressing

Start

You can

change

an C)ption

or Modifier

anytime

before

the

selected

Option

or Modifier

begins.

1.

Press PAUSE/CANCEl.

once.

2.

Select

the

new

Option

and/or

Modifiers.

3.

Press START to continue

the

cycle.

NOTE:

If you

happen

to press PAUSE/CANCEl.

twice,

the

program

clears

and

your

dryer

shuts

down.

Restart

the selection

process.

Changing

the

Preset

Dryness

Level

Settings

If all of your

loads

on

all Sensor

Dry

cycles

are consistently

not as dry

as you

would

like,

you

may change

the

preset

Dryness

level

settings

to increase

the

dryness.

This change

will

affect

all of your

Sensor

Dry

cycles.

Your Dryness

Level

settings

can be adjusted

to adapt

to different

installations,

environmental

conditions

or personal

preference.

There

are _¢drying

settings:

1 (factory

preset

dryness

level),

2 (slightly

dryer

clothes,

approximately

15%

more

drying

time)

and

3 (much

dryer

clothes,

approximately

¢0%

more

drying

time).

1.

The Dryness

kevel

settings

cannot

be changed

while

the

dryer

is running.

2.

Press and

hold

the

DRYNESS

button

for 5 seconds.

The dryer

will

beep,

and

"CF"

will

be

displayed

for

1 second

followed

by the

current

drying

setting.

3.

lb

select

a new

drying

setting,

press the

DRYNESS

button

again

until

the

desired

drying

setting

is shown.

NOTE:

While

cycling

through

the settings,

the current

setting

will

not

flash,

but

the other

settings

will

flash.

4.

Press START

to save the

drying

setting.

5.

[he

drying

setting

you

selected

will

become

your

new

preset

drying

setting

for

all Sensor

Dry

cycles.

Use the

Drying

Rack to

dry

items

such

as sweaters

and

pillows

without

tumbling.

]he

drum

turns,

but the

drying

rack does

not

move.

If your

model

does

not

have a drying

rack,

you

may

be able to

purchase

one

for

your

model.

lb

find

out

whether

your

model

allows

drying

rack

usage and for

information

on ordering,

please

refer to the

front

page of the

manual

or contact

the dealer

from

whom

you

purchased

your

dryer.

NOTE:

The drying

rack must be

removed

for normal

tumbling.

Do

not

use the

automatic

cycle

with

the drying

rack.

To use

the

drying

rack

1.

Open

dryer

door.

2.

Place

drying

rack inside

dryer

drum,

positioning

the

back

wire

on

the

ledge

of the

inner

dryer

back

paneh

Push down

on

front

edge

of

drying

rack to secure

at the front

of the

dryer.

A. Dryer rack

front edge"

B. Dryer back panel

3.

Put the

wet

items

on

top

of the drying

rack.

I.eave space

between

the

items

so air can

reach

all the

surfaces.

NOTE:

Do

not

allow

items

to

hang

over

the edge

of the

drying

rack.

!! llll1¸¸71¸!!iii!iiii_ii!!iiiiiiiiiiiiii77iiii_!!;!_7_!_!_!_!i{ii_i{{i_i{{i_i{{i_i{{i_i{{i_i{{i_i{{i_i{_

i_!!!_!_!!_!_!_ii!iii:i:i!!!!:i!i!

27

Maytag MED6600TQ Use and Care Guide - Page 27

Changing, Cycles, after, pressing, Start, Modifiers, Options, Preset, Dryness, Level, Settings,

Page 27 highlights