Maytag MER6875BAS Use and Care Guide - Page 27

froubleshootln9

Page 27 highlights

froubleshootln9 Oven did not clean properly. Oven door will not unlock after self=clean cycle. Smoothtop surface shows wear= Moisture collects on oven window or steam comes from oven vent. There is a strong odor or light smoke when oven is turned on. Fault Codes Noises may be heard. There are no beeps and no display. • Longercleaning time may be needed. ° Excessivespillovers, especially sugary and/or acidic foods, were not removed prior to the self-clean cycle. ° Oven interior is still hot. Allow about one hour for the oven to cool after the completion of a self-clean cycle, The door can be opened when LOCK is not displayed, ° The control and door may be locked, See page 9. 1. Tiny scratches or abrasions. • Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans across top. Make sure pan bottom is not rough. Use the recommended cleaning agents. See page 21. 2. Metal marks. • Do not slide metal pans across top. When cool, clean with Cooktop Cleaning Creme. See page 21. 3. Brown streaks and specks. ° Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure cooktop and pan bottom are clean. 4. Areas with a metallic sheen. ° Mineral deposits from water and food. Use recommended cleaning agents. See page 21. 5. Pitting or flaking. • Remove sugary boilovers promptly. See page 21. ° This is normal when cooking foods high in moisture. ° Excessive moisture was used when cleaning the window. • This is normal for a new range and will disappear after a few uses. Initiating a clean cycle will "burn off" the odors more quickly. • Turning on a ventilation fan will help remove the smoke and/or odor. • Excessivefood soils on the oven bottom. Use a self-clean cycle. • BAKE or LOCK may flash rapidly in the display to alert you if there is an error or a problem. If BAKE or LOCK appear in the display, press CANCEL pad. If BAKE or LOCK continue to flash, disconnect power to the appliance. Wait a few minutes, and then reconnect power. If the flashing still continues, disconnect power to the appliance and call an authorized servicer. ° If the oven is heavily soiled, excessive fiareups may result in a fault code during cleaning. Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then reset the clean cycle. If the fault code reappears, contact an authorized servicer. • The oven makes several low level noises. You may hear the oven relays as they go on and off. This is normal. • As the oven heats and cools, you may hear sounds of metal parts expanding and contracting. This is normal and will not damage your appliance. • Oven may be in Sabbath Mode. See page 16. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88

froubleshootln9
Oven did
not
clean properly.
Oven
door will
not
unlock
after
self=clean cycle.
Smoothtop
surface shows
wear=
Moisture
collects
on
oven
window
or steam
comes
from
oven
vent.
There is
a
strong odor or light
smoke when oven is
turned
on.
Fault
Codes
Noises may
be
heard.
There
are no
beeps
and
no
display.
Longer
cleaning time may be needed.
°
Excessivespillovers, especially sugary and/or acidic foods, were not removed prior
to the self-clean cycle.
°
Oven
interioris
still hot. Allow about one hour for the oven to cool after the
completion of a self-clean cycle, The door can be opened when LOCK is not
displayed,
°
The control and door may be locked, See page 9.
1. Tiny scratches or abrasions.
• Make sure cooktop and pan bottom are clean.
Do
not slide glass or metal pans
across top. Make sure pan bottom
is
not rough. Use the recommended
cleaning agents. See page 21.
2. Metal marks.
Do
not slide metal pans across top. When cool, clean with Cooktop
Cleaning Creme. See page 21.
3. Brown streaks and specks.
°
Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure
cooktop and pan bottom are clean.
4. Areas with a metallic sheen.
°
Mineral deposits from water and food. Use recommended cleaning agents.
See page 21.
5. Pitting or flaking.
Remove sugary boilovers promptly. See page 21.
°
This is normal when cooking foods high
in
moisture.
°
Excessive moisture was used when cleaning the window.
This is normal for a new range and will disappear after a few uses. Initiating a clean
cycle will "burn off" the odors more quickly.
Turning on a ventilation fan will help remove the smoke and/or odor.
Excessivefood soils on the oven bottom.
Use a self-clean cycle.
BAKE or LOCK may flash rapidly in the display to alert you if there is an error
or a problem.
If BAKE or LOCK appear in the display, press
CANCEL
pad.
If BAKE or LOCK continue to flash, disconnect power to the appliance.
Wait a few minutes, and then reconnect power. If the flashing still continues,
disconnect power to the appliance and call an authorized servicer.
°
If the oven is heavily soiled, excessive fiareups may result in a fault code during
cleaning. Press the
CANCEL
pad and allow the oven to cool completely, wipe out
excess soil, then reset the clean cycle. If the fault code reappears, contact an
authorized servicer.
The oven makes several low level noises. You may hear the oven relays as they go on
and off. This is normal.
As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
Oven may be in Sabbath Mode. See page 16.
26