Motorola RDU2020 User Guide - Page 55

Cloning Radio using the Radio to Radio, R2R Cloning Cable Optional Accessory, Operating Instructions - programming cable

Get Motorola RDU2020 - RDX UHF - Radio PDF manuals and user guides
UPC - 723755539921
View all Motorola RDU2020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory) Operating Instructions 1. Before beginning the cloning process, make sure you have: • A fully charged battery on each one of the radios. • Two Single Unit Chargers (SUC). • Turned OFF the radios and, • Both radios are of the same radio model. 2. Unplug any cables (power supply or USB cables) from the SUCs. 3. Plug one side of the cloning cable mini connector to one SUC. Plug the other end to the second SUC. Note: During the cloning process no power is being applied to the SUC. The batteries will not be charged. A data communication is being established between the two radios. 4. Turn ON the Target radio and place it into one of the SUCs. 5. On the Source radio, power the radio following the sequence below: • Long press the PTT button and SB2 simultaneously while turning the radio ON. • Wait for 3 seconds before releasing the buttons until a distinctive audible tone is heard. 6. Place the Source radio in its SUC, press and release SB1. 53 English PROGRAMMING FEATURES

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
PROGRAMMING
FEATURES
English
53
Cloning Radio using the Radio to Radio
(R2R) Cloning Cable (Optional Accessory)
Operating Instructions
1.
Before beginning the cloning process, make
sure you have:
•
A fully charged battery on each one of
the radios.
•
Two Single Unit Chargers (SUC).
•
Turned OFF the radios and,
•
Both radios are of the same radio
model.
2.
Unplug any cables (power supply or USB
cables) from the SUCs.
3.
Plug one side of the cloning cable mini
connector to one SUC. Plug the other end to
the second SUC.
Note:
During the cloning process no power is
being applied to the SUC. The batteries will
not be charged. A data communication is
being established between the two radios.
4.
Turn ON the Target radio and place it into one of
the SUCs.
5.
On the Source radio, power the radio following
the sequence below:
•
Long press the PTT button and SB2
simultaneously while turning the radio
ON.
•
Wait for 3 seconds before releasing the
buttons until a distinctive audible tone is
heard.
6.
Place the Source radio in its SUC, press and
release SB1.