Motorola RDU2020 User Guide - Page 56

What To Do if Cloning Fails, that the cloning process has failed. In the event - cloning cable

Get Motorola RDU2020 - RDX UHF - Radio PDF manuals and user guides
UPC - 723755539921
View all Motorola RDU2020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

PROGRAMMING FEATURES 7. After cloning is completed, the Source radio will sound either a 'pass' tone (cloning was successful) or a 'fail' tone (cloning process has failed). The 'pass' tone sounds like a good key 'chirp' whereas the 'fail' tone sounds similar to a 'bonk' tone. If the Source radio is a display model, it will either show 'Pass' or 'Fail' on the display (a tone will be heard within 5 seconds). 8. Once you have completed the cloning process, turn the radios OFF and ON to exit 'clone' mode. What To Do if Cloning Fails The radio will emit an audible 'bonk' indicating that the cloning process has failed. In the event that cloning fails, try performing each of the following before trying to start the cloning process again: 1. Ensure that the batteries on both radios are fully charged. 2. Check the cloning cable connection on both SUCs. 3. Ensure that the battery is engaged properly on to the radio. 4. Ensure that there is no debris in the charging tray or on the radio contacts. 5. Ensure that the Source radio is in cloning mode. 6. Ensure that the Target radio is turned ON. 7. Ensure that radios are both from the same type (same frequency band, same front panel (display/non display), same region and same transmission power). Note: This cloning cable is designed to operate only with compatible Motorola RLN6175 (Standard) and RLN6304 (Rapid) Single Unit Chargers. When ordering Cloning Cable please refer to P/ N RLN6303. For details about accessories refer to Accessories section. English 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
PROGRAMMING
FEATURES
English
54
7.
After cloning is completed, the Source radio will
sound either a ‘pass’ tone (cloning was
successful) or a ‘fail’ tone (cloning process has
failed). The ‘pass’ tone sounds like a good key
‘chirp’ whereas the ‘fail’ tone sounds similar to a
‘bonk’ tone. If the Source radio is a display
model, it will either show ‘Pass’ or ‘Fail’ on the
display (a tone will be heard within 5 seconds).
8.
Once you have completed the cloning process,
turn the radios OFF and ON to exit ‘clone’
mode.
What To Do if Cloning Fails
The radio will emit an audible ‘bonk’ indicating
that the cloning process has failed. In the event
that cloning fails, try performing each of the
following before trying to start the cloning
process again:
1.
Ensure that the batteries on both radios are fully
charged.
2.
Check the cloning cable connection on both
SUCs.
3.
Ensure that the battery is engaged properly on
to the radio.
4.
Ensure that there is no debris in the charging
tray or on the radio contacts.
5.
Ensure that the Source radio is in cloning mode.
6.
Ensure that the Target radio is turned ON.
7.
Ensure that radios are both from the same type
(same frequency band, same front panel
(display/non display), same region and same
transmission power).
Note:
This cloning cable is designed to operate
only with compatible Motorola RLN6175
(Standard) and RLN6304 (Rapid) Single
Unit Chargers.
When ordering Cloning Cable please refer to P/
N RLN6303. For details about accessories
refer to Accessories section.