Motorola RDU4160D User Guide - Page 50

OTHER PROGRAMMING FEATURES, on Channel 1 and you will not hear Channel 2.

Get Motorola RDU4160D - RDX UHF - Radio PDF manuals and user guides
UPC - 723755540309
View all Motorola RDU4160D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

PROGRAMMING FEATURES exit and save or short press the PTT button to move to the next programming feature without saving. Note: The values available for accessory microphone gain level are dependent upon maximum levels the radio supports. OTHER PROGRAMMING FEATURES Scan Scan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it will stop scanning and stays on the active channel. This allows you to listen and talk to the people on that channel without having to change the Channel Knob. If there is talking going on Channel 2 during this time, the radio will stay on Channel 1 and you will not hear Channel 2. After talking has stopped in Channel 1, the radio will wait for 5 seconds before resuming Scan again. English 48 • To start scanning, press the SB2 button (*). When the radio detects channel activity, it will stop on that channel until activity on the channel ends. You can talk to the person(s) transmitting without having to switch channels by pressing PTT. • To stop scanning, short press the SB2 button again. • If you press the PTT button while the radio is scanning, the radio will transmit on the channel which was selected before you activated Scan. If no transmission occurs within five seconds, scanning will resume. • If you want to scan a channel without Interference Eliminator Codes (CTCSS/DPL), set the code settings for the channels to '0' in the CTCSS/DPL Programming Selection Mode. Whenever the radio is set up in 'Scan Mode' the LED will signal a fast red blink. Note: (*) Assumes the SB2 button is not programmed to other function different from the default. If Auto-Scan has been enabled

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
PROGRAMMING
FEATURES
English
48
exit and save or short press the PTT button to
move to the next programming feature without
saving.
Note:
The values available for accessory
microphone gain level are dependent upon
maximum levels the radio supports.
OTHER PROGRAMMING FEATURES
Scan
Scan allows you to monitor other channels to
detect conversations.
When the radio detects a transmission, it will
stop scanning and stays on the active channel.
This allows you to listen and talk to the people
on that channel without having to change the
Channel Knob. If there is talking going on
Channel 2 during this time, the radio will stay
on Channel 1 and you will not hear Channel 2.
After talking has stopped in Channel 1, the
radio will wait for 5 seconds before resuming
Scan again.
•
To start scanning, press the SB2 button (*).
When the radio detects channel activity, it will
stop on that channel until activity on the
channel ends. You can talk to the person(s)
transmitting without having to switch channels
by pressing PTT.
•
To stop scanning, short press the SB2 button
again.
•
If you press the PTT button while the radio is
scanning, the radio will transmit on the
channel which was selected before you
activated Scan. If no transmission occurs
within five seconds, scanning will resume.
•
If you want to scan a channel without
Interference Eliminator Codes (CTCSS/DPL),
set the code settings for the channels to ‘0’ in
the CTCSS/DPL Programming Selection
Mode.
Whenever the radio is set up in ‘Scan Mode’
the LED will signal a fast red blink.
Note:
(*) Assumes the SB2 button is not
programmed to other function different from
the default. If Auto-Scan has been enabled