NEC 50XP10 User Manual - Page 26

Operation - continued Creating a Video Wall You can create a video wall consisting of up to 25 individual monitors with the built-in matrix display capability. Your Video Wall can have any of the following configurations: 2x2, 3x3, 4x4, 5x5, 5x1, 4x1, 3x1, 2x1, 1x2, 1x3, 1x4, or 1x5. Connect the signal cables as shown: 1. Select VIDEO WALL in the OPTION 3 OSD menu, then press the SET button. 2. Select the desired video wall configuration in the DIVIDER field. 3. Select POSITION in the VIDEO WALL menu, then press the SET button. Appearing on the OSD is the current video wall configuration. Select the position of the monitor for the video wall. NOTE: Each individual monitor within the video wall must have its own set position. 2x2 NO. 1 NO. 2 NO. 10 NO. 4 NO. 3 NO. 13 NO. 11 NO. 14 NO. 12 NO. 15 Video Signal RCA Phono Plug (IN) HD R VD R R IN R L OUT IN EXTERNAL CONTROL DVI L(MONO) AUDIO3 VGA R/Cr/Pr G/Y B/Cb/pb L(MONO) AUDIO2 Y Cr/Pr Cb/Pb DVD/HD1 L(MONO) AUDIO1 S-VIDEO IN IN/OUT VIDEO SPEAKER (S) RGBHV / DVD/HD2 AC IN BNC connector (OUT) to another display RGB/DVD/HD Signal OUT R HD VD BNC connector (IN) R R IN R L IN EXTERNAL CONTROL DVI L (MONO) AUDIO3 VGA R/Cr/Pr G/Y B/Cb/pb L(MONO) AUDIO2 Y Cr/Pr Cb/Pb DVD/HD1 L(MONO) AUDIO1 S-VIDEO IN IN/OUT VIDEO SPEAKER (S) RGBHV / DVD/HD2 AC IN VGA connector (OUT) to another display 3x3 NO. 7 NO. 8 NO. 9 NOTE: 1. The VIDEO 1 and VGA terminals may be used either for INPUT or OUTPUT. Do not connect an OUTPUT signal from another unit when LOOP OUT in the OPTION 3 OSD is set to ON, as it may damage the other unit due to an extraordinary load. 2. While signals are input to the VGA terminal, LOOP OUT should not be turned ON. Information: Set the LOOP OUT in OPTION3 to ON to loop signals out to another plasma display. • Set the VIDEO WALL options properly when creating a video wall. • Use the appropriate (length and efficiency) BNC cable to connect monitors. • If the image quality is poor, do not use the monitor out terminal to link to another monitor. Use a commercially available distribution amplifier to connect the split signal to the appropriate monitor INPUT terminals. • For a resolution of 1024x768 at 60 Hz (or lower), the maximum recommended size for a viewing wall is 4 displays. • A distribution amplifier is highly recommended when setting up a 3 x 3 (or greater) video wall. • When looping from plasma to plasma, an appropriate (length and efficiency) 15-pin male mini D-Sub - 5BNC conversion cable is required. 4x4 NO. 16 NO. 17 NO. 18 NO. 19 NO. 20 NO. 21 NO. 22 NO. 23 NO. 24 NO. 25 NO. 26 NO. 27 NO. 28 NO. 29 NO. 30 NO. 31 5x5 NO. 32 NO. 33 NO. 34 NO. 35 NO. 36 NO. 37 NO. 38 NO. 39 NO. 40 NO. 41 NO. 42 NO. 43 NO. 44 NO. 45 NO. 46 NO. 47 NO. 48 NO. 49 NO. 50 NO. 51 NO. 52 NO. 53 NO. 54 NO. 55 NO. 56 5x1 NO. 1 NO. 2 NO. 3 NO. 4 NO. 5 1x5 NO. 1 NO. 2 NO. 3 NO. 4 NO. 5 1x4 NO. 1 NO. 2 NO. 3 NO. 4 1x3 NO. 1 NO. 2 NO. 3 1x2 NO. 1 NO. 2 4x1 NO. 1 NO. 2 NO. 3 NO. 4 3x1 NO. 1 NO. 2 NO. 3 2x1 NO. 1 NO. 2 Video Wall Configurations English-23