NEC LCD1830 MultiSync LCD1830 User's Manual - Page 8

Remove Monitor Stand for Mounting - screen

Get NEC LCD1830 - MultiSync - 18.1inch LCD Monitor PDF manuals and user guides
UPC - 805736000658
View all NEC LCD1830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Quick Start -continued Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Remove Monitor Stand for Mounting Figure TS.1 To prepare the monitor for alternate mounting purposes: 1. Remove the connector cover, hinge cover and cable cover (Figure R.1). 2. Disconnect all cables. 3. Place monitor face down on a non-abrasive surface ( place the screen on a 32 mm platform so that hole of stand match to screw location). (Figure R.2). PUSH PUSH 4. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure R.2) the monitor is now ready for mounting in an alternate manner. Figure R.1 5. Connect the AC cord and signal cable to the back of the monitor. 6. Reverse this process to 32mm reattach stand. Figure R.2 Caution: To fulfil the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). Screws LCD1830.wpc 6 8 11/29/00, 9:56 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
6
Quick Start
–continued
Screws
32mm
Tilt
Grasp both sides of the monitor screen with your hands
and adjust the tilt as desired
(Figure TS.1).
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1.
Remove the connector cover, hinge cover
and cable cover
(Figure R.1).
2.
Disconnect all cables.
3.
Place monitor face down
on a non-abrasive
surface ( place the screen
on a 32 mm platform so
that hole of stand match to
screw location).
(Figure R.2).
4.
Remove the 4 screws
connecting the
monitor to the stand
and lift off the stand assembly
(Figure R.2)
the monitor is
now ready for mounting in an
alternate manner.
5.
Connect the AC cord and signal
cable to the back of the monitor.
6.
Reverse this process to
reattach stand.
Caution:
To fulfil the safety requirements
the monitor must be mounted to
an arm which guaranties the
necessary stability under
consideration of the weight of the
monitor. The LCD monitor shall
only be used with an approved
arm (e.g. GS mark).
Figure TS.1
Figure R.1
Figure R.2
PUSH
PUSH
LCD1830.wpc
11/29/00, 9:56 AM
8