Netgear RP614 RP614v4 Reference Manual - Page 33

Erasing the Configuration, Upgrading the Router Software - default login

Get Netgear RP614 - Web Safe Router PDF manuals and user guides
UPC - 606449023022
View all Netgear RP614 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

RP614v4 Cable/DSL Router Reference Manual Erasing the Configuration It is sometimes desirable to restore the router to the factory default settings. This can be done by using the Erase function, which will restore all factory settings. After an erase, the router's password will be password, the LAN IP address will be 192.168.1.1, and the router's DHCP client will be enabled. To erase the configuration, click the Erase button. To restore the factory default configuration settings without knowing the login password or IP address, you must use the Default Reset button on the rear panel of the router. See "Restoring the Default Configuration and Password" on page 5-7. Upgrading the Router Software Note: Before upgrading the router software, use the router backup utility to save your configuration settings. Any router upgrade will revert the router settings back to the factory defaults. After completing the upgrade, you can restore your settings from the backup. The routing software of the RP614v4 router is stored in FLASH memory, and can be upgraded as new software is released by NETGEAR. Upgrade files can be downloaded from the NETGEAR Web site. If the upgrade file is compressed (.ZIP file), you must first extract the binary (.BIN) file before sending it to the router. The upgrade file can be sent to the router using your browser. Note: The Web browser used to upload new firmware into the RP614v4 router must support HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer or Netscape Navigator 4.0 or higher. Maintenance 3-7 v3.1, June 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
RP614v4 Cable/DSL Router Reference Manual
Maintenance
3-7
v3.1, June 2008
Erasing the Configuration
It is sometimes desirable to restore the router to the factory default settings. This can be done by
using the Erase function, which will restore all factory settings. After an erase, the router's
password will be
password
, the LAN IP address will be 192.168.1.1, and the router's DHCP client
will be enabled.
To erase the configuration, click the
Erase
button.
To restore the factory default configuration settings without knowing the login password or IP
address, you must use the Default Reset button on the rear panel of the router. See
“Restoring the
Default Configuration and Password” on page 5-7
.
Upgrading the Router Software
The routing software of the RP614v4 router is stored in FLASH memory, and can be upgraded as
new software is released by NETGEAR. Upgrade files can be downloaded from the NETGEAR
Web site. If the upgrade file is compressed (.ZIP file), you must first extract the binary (.BIN) file
before sending it to the router. The upgrade file can be sent to the router using your browser.
Note:
Before upgrading the router software, use the router backup utility to save your
configuration settings. Any router upgrade will revert the router settings back to
the factory defaults. After completing the upgrade, you can restore your settings
from the backup.
Note:
The Web browser used to upload new firmware into the RP614v4 router must
support HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer
or Netscape Navigator 4.0 or higher.