Netgear SW510 Installation Guide - Page 11

Conformity to the ISO/IEC 8802-3 and ANSI/IEEE 802.3 10BASE-T standards

Get Netgear SW510 - Switch PDF manuals and user guides
UPC - 606449000955
View all Netgear SW510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installation Guide for the Model SW510 and Model SW518 Ethernet Switches • Two 10/100 Mbps ports on each of the switches One of the 10/100 Mbps ports is configurable as Normal (MDI-X) or Uplink (MDI). • Switch-selectable half/full-duplex mode for the 10 Mbps ports In full-duplex mode, the throughput of point-to-point connections is doubled by enabling individual ports to transmit and receive concurrently when the other end also supports full-duplex mode. • Auto- or full-duplex mode for the 10/100 Mbps ports: - Auto-negotiable between full-duplex and half-duplex mode when set in auto-duplex mode The mode will default to half-duplex transmission if the remote end cannot provide a proper signal to indicate its own capability. - Can be set to full-duplex mode permanently for interoperability with legacy 100BASE-TX devices • Wire-speed filtering and forwarding to provide "traffic cop" function by directing traffic to the appropriate route without slowing down the traffic • Plug-and-Play operation with no software to configure • Low latency store-and-forward transmission mode with leading edge to leading edge of less than 75 µs • Ten vista RJ-45 connector ports on the Model SW510 and eighteen vista RJ-45 connector ports on the Model SW518 switch Each port has built-in LEDs to monitor individual port status. • Comprehensive LED indicator panel to monitor overall switching condition • Auto address learning function to build the routing information database The routing table contains 8,000 Ethernet address entries per port to store MAC addresses for attached network nodes. • 2-megabyte (MB) buffer provided for the 10 Mbps ports on the Model SW518 and 1 MB buffer provided for the 10 Mbps ports on the Model SW510, with an additional 2 MB of buffer memory for the two 10/100 Mbps ports • Conformity to the ISO/IEC 8802-3 and ANSI/IEEE 802.3 10BASE-T standards • Conformity to the IEEE 802.3u 100BASE-TX standard • Rack Mount Kit provided for installing the switch in a standard 19-inch rack Introduction 1-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
Installation Guide for the Model SW510 and Model SW518 Ethernet Switches
Introduction
1-3
•
Two 10/100 Mbps ports on each of the switches
One of the 10/100 Mbps ports is configurable as Normal (MDI-X) or Uplink (MDI).
•
Switch-selectable half/full-duplex mode for the 10 Mbps ports
In full-duplex mode, the throughput of point-to-point connections is doubled by enabling
individual ports to transmit and receive concurrently when the other end also supports
full-duplex mode.
•
Auto- or full-duplex mode for the 10/100 Mbps ports:
—
Auto-negotiable between full-duplex and half-duplex mode when set in auto-duplex mode
The mode will default to half-duplex transmission if the remote end cannot provide a
proper signal to indicate its own capability.
—
Can be set to full-duplex mode permanently for interoperability with legacy 100BASE-TX
devices
•
Wire-speed filtering and forwarding to provide “traffic cop” function by directing traffic to the
appropriate route without slowing down the traffic
•
Plug-and-Play operation with no software to configure
•
Low latency store-and-forward transmission mode with leading edge to leading edge of less
than 75
µ
s
•
Ten vista RJ-45 connector ports on the Model SW510 and eighteen vista RJ-45 connector
ports on the Model SW518 switch
Each port has built-in LEDs to monitor individual port status.
•
Comprehensive LED indicator panel to monitor overall switching condition
•
Auto address learning function to build the routing information database
The routing table contains 8,000 Ethernet address entries per port to store MAC addresses for
attached network nodes.
•
2-megabyte (MB) buffer provided for the 10 Mbps ports on the Model SW518 and 1 MB
buffer provided for the 10 Mbps ports on the Model SW510, with an additional 2 MB of buffer
memory for the two 10/100 Mbps ports
•
Conformity to the ISO/IEC 8802-3 and ANSI/IEEE 802.3 10BASE-T standards
•
Conformity to the IEEE 802.3u 100BASE-TX standard
•
Rack Mount Kit provided for installing the switch in a standard 19-inch rack