Oki OkiPOS406 OkiPOS406 Users Guide - Page 99

A-2. Auto Cutter Specifications, A-3. Interface, A-4. Electrical Characteristics, A-5. Option

Get Oki OkiPOS406 PDF manuals and user guides View all Oki OkiPOS406 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

A-2. Auto Cutter Specifications (1) Cutting frequency Max. 20 cuts per minute (2) Thickness of paper 65~85 µm A-3. Interface RS232C serial interface or Two-way parallel interface (IEEE1284) A-4. Electrical Characteristics (1) Input Voltage (2) Current Consumption (3) Power Connector DC 24V±10% Operating: Approx. 1.3 A (at ASCII printing) Peak: Approx. 8 A (at print duty 100%, for 10 seconds or less) Stand-by: Approx. 0.05 A Pin No. 1 2 3 Shell Function DC24V Signal GND N.C. Frame ground 13 2 APPENDIX Important! • When using a printer power supply other than the optional AC adaptor (PS60-24A), be sure that the following cautions are observed. • Use a power supply of DC 24 V ±10% and more than 2.0 A (5.0 A Load 10 sec. Min) with SELV output approved by IEC60950. • Be careful about installing the printer in an area where there is noise. Take the appropriate measures to protect against electrostatic AC line noise, etc. A-5. Option (1) Wall Mount Set (WB-T600) (2) Vertical Stand Set (VS-T600) (3) USB Interface Board Unit (IFBD-HU04) (4) Parallel Interface Board Unit (IFBD-HC04) (5) 25 Pin RS-232C Interface Board Unit (IFBD-HD04) (6) 9 Pin RS-232C Interface Board Unit (IFBD-HN04) - 96 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
– 96 –
APPENDIX
A-2.
Auto Cutter Specifications
(1)Cutting frequency
Max. 20 cuts per minute
(2)Thickness of paper
65~85
μ
m
A-3. Interface
RS232C serial interface or Two-way parallel interface (IEEE1284)
A-4.
Electrical Characteristics
(1)Input Voltage
DC 24V±10%
(2)Current Consumption
Operating:
Approx. 1.3 A (at ASCII printing)
Peak:
Approx. 8 A (at print duty 100%,
for 10 seconds or less)
Stand-by:
Approx. 0.05 A
(3)Power Connector
Pin No.
Function
1
DC24V
2
Signal GND
3
N.C.
Shell
Frame ground
1
3
2
<Viewed from Connector Surface>
Important!
•
When using a printer power supply other than the optional AC adaptor
(PS60-24A), be sure that the following cautions are observed.
•
Use a power supply of DC 24 V ±10% and more than 2.0 A (5.0 A Load
10 sec. Min) with SELV output approved by IEC60950.
•
Be careful about installing the printer in an area where there is noise.
Take the appropriate measures to protect against electrostatic AC line
noise, etc.
A-5. Option
(1)Wall Mount Set (WB-T600)
(2)Vertical Stand Set (VS-T600)
(3) USB Interface Board Unit (IFBD-HU04)
(4) Parallel Interface Board Unit (IFBD-HC04)
(5) 25 Pin RS-232C Interface Board Unit (IFBD-HD04)
(6) 9 Pin RS-232C Interface Board Unit (IFBD-HN04)