Oki PM4410 Guide: Setup, PM4410 (English) - Page 23

Load Paper

Get Oki PM4410 PDF manuals and user guides View all Oki PM4410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Load Paper Front Feed Continuous Forms Paper Specifications: Front Feed Maximum thickness: 0.031 inches (0.79 mm) Type Single Part Carbonless (1 + 9 max.) Interleaf (1 + 6 max) Labels Envelopes Card Stock Weight 12 to 24 lb. (45 to 90 g/m2) 9 to 11 lb. (34 to 41 g/m2) Width 3* to 16.5 inches (76 to 419 mm) 3* to 16.5 inches (76 to 419 mm) 9 to 14 lb. (34 to 52.5 g/m2) 9 lb. (34 g/m2) carbon 0.011 inch (0.28 mm) thick 24 lb. (90 g/m2) max. 100 lb. (375 g/m2) max. 3* to 16.5 inches (76 to 419 mm) 3¼ to 15 inches (83 to 381 mm) 3 to 10 inches (76 to 254 mm) 3 to 8 inches (76 to 203 mm) * For paper widths less than 5 inches (127 mm), remove the support between the tractors. When using paper which is thicker than 7-part carbonless or its equivalent, you must enter the Menu mode, then go to the Impact Mode item in the Set-Up group and select High Impact Copy as the setting. To load front-feed continuous forms: Preparation 1. Position the printer at the front edge of the support (this promotes the unrestricted flow of paper into the printer), then place a stack of continuous forms below the printer. Recommended height of printer support, 29.5 inches (750 mm). Pacemark 4410 Setup Guide E-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
E-21
Pacemark 4410 Setup Guide
Load Paper
Front Feed Continuous Forms
Paper Specifications: Front Feed
Maximum thickness:
0.031 inches (0.79 mm)
Type
Weight
Width
Single Part
12 to 24 lb. (45 to 90 g/m
2
)
3* to 16.5 inches (76 to 419 mm)
Carbonless
9 to 11 lb. (34 to 41 g/m
2
)
3* to 16.5 inches (76 to 419
mm)
(1 + 9 max.)
Interleaf
9 to 14 lb. (34 to 52.5 g/m
2
)
3* to 16.5 inches (76 to 419
mm)
(1 + 6 max)
9 lb.
(34 g/m
2
) carbon
Labels
0.011 inch (0.28 mm) thick
3ΒΌ to 15 inches (83 to 381 mm)
Envelopes
24 lb. (90 g/m
2
) max.
3 to 10 inches (76 to 254 mm)
Card Stock
100 lb. (375 g/m
2
) max.
3 to 8 inches (76 to 203 mm)
*
For paper widths less than 5 inches (127 mm), remove the support between the
tractors.
When using paper which is thicker than 7-part carbonless or
its equivalent, you must enter the Menu mode, then go to the
Impact Mode
item in the
Set-Up
group and select
High
Impact Copy
as the setting.
To load front-feed continuous forms:
Preparation
1. Position the printer at the front edge of the support (this promotes the
unrestricted flow of paper into the printer), then place a stack of
continuous forms below the printer. Recommended height of printer
support, 29.5 inches (750 mm).