Oki PM4410 Guide: Setup, PM4410 (English) - Page 28

Rear Feed Continuous Forms, Paper Specifications: Rear Feed, Preparation

Get Oki PM4410 PDF manuals and user guides View all Oki PM4410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Rear Feed Continuous Forms Paper Specifications: Rear Feed Maximum thickness: 0.014 inch (0.36 mm) Type Single Part Carbonless (1 + 5 max.) Interleaf (1 + 3 max) Weight 12 to 24 lb. (45 to 90 g/m2) 9 to 11 lb. (34 to 41 g/m2) Width 3* to 16.5 inches (76 to 419 mm) 3* to 16.5 inches (76 to 419 mm) 9 to 14 lb. (34 to 52.5 g/m2) 3* to 16.5 inches (76 to 419 mm) 9 lb. (34 g/m2) carbon * For paper widths less than 4 inches (102 mm), remove the support between the tractors. When using paper which is thicker than 7-part carbonless or its equivalent, you must enter the Menu mode, then go to the Impact Mode item in the Set-Up group and select High Impact Copy as the setting. To load rear-feed paper: Preparation 1. Position the printer at the rear edge of the support (this promotes the unrestricted flow of paper into the printer), then place a stack of continuous forms below the printer. Recommended height of printer support, 29.5 inches (750 mm). E-26 Pacemark 4410 Setup Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
E-26
Pacemark 4410 Setup Guide
Rear Feed Continuous Forms
Paper Specifications: Rear Feed
Maximum thickness: 0.014 inch (0.36 mm)
Type
Weight
Width
Single Part
12 to 24 lb. (45 to 90 g/m
2
)
3* to 16.5 inches (76 to 419 mm)
Carbonless
9 to 11 lb. (34 to 41 g/m
2
)
3* to 16.5 inches (76 to 419
mm)
(1 + 5 max.)
Interleaf
9 to 14 lb. (34 to 52.5 g/m
2
)
3* to 16.5 inches (76 to 419
mm)
(1 + 3 max)
9 lb.
(34 g/m
2
) carbon
*
For paper widths less than 4 inches (102 mm), remove the support between the
tractors.
When using paper which is thicker than 7-part carbonless or
its equivalent, you must enter the Menu mode, then go to the
Impact Mode
item in the
Set-Up
group and select
High
Impact Copy
as the setting.
To load rear-feed paper:
Preparation
1. Position the printer at the rear edge of the support (this promotes the
unrestricted flow of paper into the printer), then place a stack of
continuous forms below the printer. Recommended height of printer
support, 29.5 inches (750 mm).