Onkyo PR-SC5509 Owner Manual - Page 66
Hardware Setup, Remote ID, Multi Zone, Tuner
View all Onkyo PR-SC5509 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 66 highlights
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TUNER, TV/CD, PHONO, PORT, NET, USB ` Off: No trigger signal is output. A 12-volt trigger signal is output when the connected component is selected as the source for: `Main, Zone 2, Main/Zone 2, Zone 3, Main/Zone 3, Zone 2/Zone 3, Main/Zone 2/Zone 3 Note • By default, all input sources on the "12V Trigger A Setup" menu are set to "Main", those on "12V Trigger B Setup" are set to "Main/Zone 2/Zone 3", and those on "12V Trigger C Setup" are set to "Zone 2". Hardware Setup Main menu Hardware Setup Remote ID ■ Remote ID `1, 2, or 3 When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV controller from the other components, you can change its remote ID from "1", to "2" or "3". Note • If you do change the AV controller's remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won't be able to control it with the remote controller. Changing the remote controller's ID 1 While holding down RECEIVER, press and hold down SETUP until RECEIVER lights (about 3 seconds) (➔ page 48). 2 Use the number buttons to enter ID 1, 2, or 3. RECEIVER flashes twice. Multi Zone ■ Zone 2 Out, Zone 3 Out ` Fixed: The Zone 2/3 volume must be set on the amp in that zone. ` Variable: The Zone 2/3 volume can be set on the AV controller. If you've connected your Zone 2/3 speakers to an amp with no volume control, set the "Zone 2 Out" and "Zone 3 Out" setting, respectively, to "Variable" so that you can set the volume, balance, and tone of zone 2 and volume of zone 3 on the AV controller. ■ Zone 2 Maximum Volume, Zone 3 Maximum Volume `Off, 50 to 99 (Absolute display) `Off, -32dB to +17dB (Relative display) With this setting, you can limit the maximum volume for Zone 2/3. ■ Zone 2 Power On Volume, Zone 3 Power On Volume `Last, Min, 1 to 99 or Max (Absolute display) `Last, -2dB, -81dB to +18dB (Relative display) This setting determines what the volume will be for Zone 2/3 each time the AV controller is turned on. To use the same volume level as when the AV controller was last turned off, select "Last". The "Zone 2 Power On Volume" and "Zone 3 Power On Volume" cannot be set higher than the "Zone 2 Maximum Volume" and "Zone 3 Maximum Volume" setting. ■ Zone 2 Component Video Out ` Yes: Select if a TV in Zone 2 is connected to the COMPONENT VIDEO ZONE 2 OUT. ` No: Select if no TV in Zone 2 is connected to the COMPONENT VIDEO ZONE 2 OUT. If you've connected the COMPONENT VIDEO ZONE 2 OUT to a TV in Zone 2, set this setting to "Yes". Note • If the "Zone 2 Component Video Out" setting is set to "No", the same video signal as COMPONENT VIDEO MONITOR OUT is output from ZONE 2 OUT (component). Tuner For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets will be deleted. ■ AM/FM Frequency Step (North American models) ` 10kHz/200kHz: ` 9kHz/50kHz: Select the frequency step according to your area. ■ AM Frequency Step (European and Asian models) ` 10kHz: ` 9kHz: Select the frequency step according to your area. En 66