Onkyo TX-NR818 Owner Manual - Page 52

Note *1 • The video preview is not displayed when: - HDMI IN 5/6/7 is the current HDMI input source, or - No signal is present on the current input source. • The video of the currently-selected input is displayed on the main screen, not on a preview thumbnail. *2 "Dolby Volume", "Dynamic EQ" and "Dynamic Volume" cannot be selected when any of the THX listening modes is selected, with "Loudness Plus" set to "On" or "Preserve THX Settings" set to "Yes" (➔ page 62). *3 When "Dynamic EQ" is set to "On" or "Dynamic Volume" is set to anything else than "Off", "Dolby Volume" will be switched to "Off" (➔ page 65). *4 • When the "Monitor Out" setting is set to "Sub", "Video" cannot be selected (➔ page 57). • This setting cannot be used with the NET input selector. *5 Only when you have selected "Custom" in the "Picture Mode" (➔ page 70), pressing ENTER allows you to adjust the following items via the Quick Setup: "Brightness", "Contrast", "Hue" and "Saturation". Press RETURN to return to the "Picture Mode" setting. *6 Depending on the input source and listening mode, not all channels shown here output the sound. *7 • This setting is not available in either of the following cases: - The "Audio TV Out" setting is set to "On" (➔ page 75). - "HDMI Control(RIHD)" is set to "On" (➔ page 75) and you're listening through your TV speakers. Using the Audio Settings of Quick Setup You can change various audio settings from the Quick Setup (➔ page 51). Note • These settings are not available in either of the following cases: - The "Audio TV Out" setting is set to "On" (➔ page 75). - "HDMI Control(RIHD)" is set to "On" (➔ page 75) and you're listening through your TV speakers. Sound Program ■ Sound Program ` Stereo Source 1, Stereo Source 2, Stereo Source 3, Multich Source 1, Multich Source 2, Multich Source 3 ` Off With this setting, you can select the combination of settings that you registered in "Sound Program Edit" (➔ page 66). Note • If the input selector is changed, the "Sound Program" setting is switched back to "Off". Tone Control ■ Bass ` -10dB to 0dB to +10dB in 2 dB steps You can boost or cut low-frequency sounds output from the front speakers. ■ Treble ` -10dB to 0dB to +10dB in 2 dB steps You can boost or cut high-frequency sounds output from the front speakers. You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio or THX listening mode is selected. Advanced Operations Operating on the AV receiver 1 Press TONE repeatedly to select either "Bass" or "Treble". 2 Use - and + to adjust. Speaker Levels ■ Subwoofer Level `-15.0dB to 0.0dB to +12.0dB in 0.5 dB steps ■ Center Level `-12.0dB to 0.0dB to +12.0dB in 0.5 dB steps You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to "Level Calibration" (➔ page 61) before setting the AV receiver to standby. Note • You cannot use these function while the AV receiver is muted. • These settings cannot be used while a pair of headphones is connected. • Speakers that are set to "No" or "None" in "Speaker Configuration" (➔ page 60) cannot be adjusted. • When "Sound Program" is enabled, "Subwoofer Level" cannot be used if the "Subwoofer" setting is set to "No" in "Sound Program Edit". En-52