Onkyo TX-NR818 Owner Manual - Page 60

Note • If the "Speakers Type (Front)" setting is set to "Bi-Amp" or "Digital Crossover", Powered Zone 2 cannot be used. • When the "Powered Zone 2" setting is set to "Yes" and Zone 2 is turned on, the surround back and front high speakers cannot be used. • If the "Powered Zone 2" setting is set to "No", the "Powered Zone 3" setting cannot be selected. • "Preout to External Amplifier" is not available in either of the following cases: - The "Speakers Type (Front)" setting is set to "Bi-Amp" or "Digital Crossover". - The "Powered Zone 2" setting is set to "Yes". Speaker Configuration This setting is set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup (➔ page 37). With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify "Full Band" for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey MultEQ XT32 Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to "80Hz(THX)" crossover. ■ Subwoofer ` Yes ` No ■ Front ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz Note • If the "Subwoofer" setting is set to "No", the "Front" setting is fixed at "Full Band". ■ Center*1, Surround*1*2 ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None ■ Front Wide*1*3*4*6*8, Front High*1*3*5*6*7*8 ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None ■ Surround Back*1*2*3*5*6*8 ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None Note *1 "Full Band" can be selected only when "Full Band" is selected in the "Front" setting. *2 When the "Powered Zone 3" setting is set to "Yes" and Zone 3 is turned on, this setting cannot be selected. *3 This setting cannot be selected if the "Speakers Type (Front)" setting is set to "Bi-Amp" or "Digital Crossover". *4 When the "Powered Zone 2" setting is set to "Yes", this setting cannot be selected. *5 When the "Powered Zone 2" setting is set to "Yes" and Zone 2 is turned on, this setting cannot be selected. *6 If the "Surround" setting is set to "None", this setting cannot be selected. *7 When the "Powered Zone 3" setting is set to "Yes", this setting cannot be selected. *8 If the "Preout to External Amplifier" setting is enabled for these speakers, "None" cannot be selected. ■ Surround Back Ch ` 1ch: Select if only one surround back speaker L is connected. Advanced Operations ` 2ch: Select if two (left and right) surround back speakers are connected. Note • If the "Surround Back" setting is set to "None", this setting cannot be selected. ■ LPF of LFE (Low-Pass Filter for the LFE Channel) `80Hz, 90Hz, 100Hz, 120Hz ` Off: Low-Pass Filter is not applied. With this setting, you can specify the cutoff frequency of the LFE channel's low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel. Note • If you're using THX-certified speakers, select "80Hz". ■ Subwoofer Phase ` 0º ` 180º: Moves the subwoofer phase. Note • If the "Subwoofer" setting is set to "No", this setting cannot be selected. En-60