Home » Onkyo Manuals » Audio Receivers » Onkyo TX-NR818 » Manual Viewer

Onkyo TX-NR818 Owner Manual - Page 80

En-80, Adjusting the Volume for Zones, Muting Zones

Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

2 To select an input source for Zone 2/3, press ZONE repeatedly, followed by an INPUT SELECTOR button. To select AM or FM, press the TUNER input selector and ZONE repeatedly. 3 To turn off Zone 2/3, press ZONE repeatedly, followed by RECEIVER. The zone is turned off. Tip • The corresponding trigger output goes low (0 volts). Adjusting the Volume for Zones ■ Operating on the remote controller 1 Press ZONE repeatedly. 2 Use VOL R/X. ■ Operating on the AV receiver 1 Press ZONE 2 or ZONE 3 (the Z2/Z3 indicator on the AV receiver's display flashes). 2 Use MASTER VOLUME control within 8 seconds. If your Zone 2/3 speakers are connected to a receiver or integrated amplifier in Zone 2/3, use its volume control to adjust the volume. Muting Zones ■ Operating on the remote controller 1 Press ZONE repeatedly, and then press MUTING. Tip • To unmute, press ZONE followed by MUTING again. Zones can also be unmuted by adjusting the volume. Note • Only analog input sources are output by the ZONE 2/3 LINE OUT and FRONT WIDE/ZONE 2 L/R, FRONT HIGH/ZONE 3 L/R terminals. Digital input sources are not output. If no sound is heard when an input source is selected, verify that the source is connected to an analog input. • You cannot select different AM or FM radio stations for your main room and Zone 2/3. The same AM/FM radio station will be heard in each room. Namely, if you have selected an FM station for the main room, that station will also be output in Zone 2/3. • When you have selected NET or USB as input selector, the last selector selected will be set for Main room and Zone 2/3. • When Zone 2/3 is activated and its input selector is selected, the power consumption of standby mode slightly increases. • While Zone 2/3 is on, V functions will not work. • When setting the AV receiver to standby mode while Zone 2/3 is active, the Z2 or Z3 indicator is dimly lit. • Activating Zones in the main room when the listening mode is set to Pure Audio will automatically switch it to Direct. • "GAME2" cannot be selected as input sources for Zone 2/3. • When "GAME2" is the input source of Main room and Zone 2/3 is set to share the same source, no sound will be output from Zone 2/3. • Even if you repeatedly press the remote controller's ZONE to select zones, the last zone selection will be retained once you have switched to other components by pressing other REMOTE MODE after pressing ZONE. En-80 Advanced Operations

Section	Page
Safety Information and Introduction	2
Important Safety Instructions	2
Precautions	3
Supplied Accessories	5
Table of Contents	6
Features	7
Front & Rear Panels	8
Remote Controller	12
Connections	13
Connecting the AV Receiver	13
Connecting Your Speakers	13
About AV Connections	18
Connecting Components with HDMI	19
Connecting Your Components	20
Connecting Onkyo RI Components	21
Connecting the Antennas	22
Connecting the Power Cord	22
Turning On & Basic Operations	23
Turning On/Off the AV Receiver	23
Turning On	23
Turning Off	23
Initial Setup	24
Selecting the Language for the Onscreen Setup Menus	24
Audyssey MultEQ XT32: Auto Setup	24
Source Connection	25
Remote Mode Setup	25
Network Connection	25
Terminating the Initial Setup	25
Playback	26
Playing the Connected Component	26
Controlling Contents of USB or Network Devices	27
Understanding Icons on the Display	28
Playing an iPod/iPhone via USB	28
Playing a USB Device	29
Listening to vTuner Internet Radio	29
Registering Other Internet Radio	30
Changing the Icon Layout on the Network Service Screen	31
Playing Music Files on a Server (DLNA)	31
Remote Playback	32
Playing Music Files on a Shared Folder	33
Listening to AM/FM Radio	34
Playing Audio and Video from Separate Sources	36
Using Basic Functions	37
Using the Automatic Speaker Setup	37
Using the Listening Modes	40
Using the Home Menu	47
Using the Sleep Timer	48
Setting the Display Brightness	48
Displaying Source Information	48
Changing the Input Display	48
Using the Whole House Mode	49
Selecting Speaker Layout	49
Muting the AV Receiver	49
Using Headphones	49
Using Easy Macros	50
Advanced Operations	51
On-screen Setup	51
Using the Quick Setup	51
Using the Audio Settings of Quick Setup	52
Using the Setup Menu (HOME)	55
About the HYBRID STANDBY Indicator	56
Setup Menu Items	56
Input/Output Assign	57
Speaker Setup	59
Audio Adjust	64
Source Setup	67
Listening Mode Preset	72
Miscellaneous	73
Hardware Setup	74
Remote Controller Setup	77
Lock Setup	77
Multi Zone	78
Making Multi Zone Connections	78
Controlling Multi Zone Components	79
Using the Remote Controller in Zone and Multiroom Control Kits	81
Controlling Other Components	82
iPod/iPhone Playback via Onkyo Dock	82
Using the Onkyo Dock	82
Controlling Your iPod/iPhone	83
Controlling Other Components	84
Preprogrammed Remote Control Codes	84
Looking up for Remote Control Codes	84
Entering Remote Control Codes	85
Remapping Colored Buttons	85
Remote Control Codes for Onkyo Components Connected via RI	86
Resetting the REMOTE MODE Buttons	86
Resetting the Remote Controller	86
Controlling Other Components	86
Learning Commands	89
Using Normal Macros	90
Appendix	91
Troubleshooting	91
Firmware Update	97
Connection Tips and Video Signal Path	101
Using an RIHD-compatible TV, Player, or Recorder	104
About HDMI	106
Network/USB Features	107
License and Trademark Information	110
Specifications	111
Internet Radio Guide	113
Using Internet Radio	113
Common Procedures in Internet Radio Menu	113
Pandora(R) internet radio -Getting Started (U.S. only)	114
Using Rhapsody (U.S. only)	115
Using the SiriusXM Internet Radio (North American only)	116
Using Last.fm Internet Radio	117
Using Slacker Personal Radio	118
Using MP3tunes	119
Utilisation d’une webradio	120
Procédures courantes dans le menu de webradio	120
Pandora(R) internet Radio -Pour commencer (États-Unis uniquement)	121
Utilisation de Rhapsody (Etats-Unis uniquement)	122
Utilisation de SiriusXM Internet Radio (Amérique du Nord uniquement)	123
Utilisation de la webradio Last.fm	124
Utilisation de Slacker Personal Radio	125
Uso de Internet Radio	126
Procedimientos comunes en el menú Internet Radio	126
Pandora(R) Internet Radio -Primeros pasos (solo EE.UU.)	127
Uso de Rhapsody (sólo EE.UU.)	128
Uso de SiriusXM Internet Radio (solo Norteamérica)	129
Uso de Last.fm Internet Radio	130
Uso de Slacker Personal Radio	131
Using Internet Radio	133
Common Procedures in Internet Radio Menu	133
Using Last.fm Internet Radio	134
Internetradio verwenden	135
Allgemeine Verfahren bei den Internetradio-Menüs	135
Verwendung von Last.fm Internet Radio	136
Remote Control Codes	137
Dedicated Onkyo Receiver	142
Cable Set Top Box	142
Cable/PVR Combination	142
IPTV	142
IPTV/PVR Combination	142
CD	143
CD-R	143
MD	143
Cassette Deck	143
Accessory	143
Video - Accessory	144
Receiver	144
Satellite Set Top Box	144
Satellite Set Top Box	146
SAT/PVR Combination	146
Television	146
VCR	151
PVR	151
TV/VCR Combination	151
DVD	152
Blu-ray Disc	153
DVD-R	153
HD-DVD	154

Match case Limit results 1 per page

Advanced Operations

En-80

Adjusting the Volume for Zones

■

Operating on the remote controller

■

Operating on the AV receiver

If your Zone 2/3 speakers are connected to a receiver or

integrated amplifier in Zone 2/3, use its volume control to

adjust the volume.

Muting Zones

■

Operating on the remote controller

Tip

•

To unmute, press

ZONE

followed by

MUTING

again. Zones can

also be unmuted by adjusting the volume.

Note

•

Only analog input sources are output by the

ZONE 2/3 LINE

OUT

and

FRONT WIDE/ZONE 2 L/R

FRONT

HIGH/ZONE 3 L/R

terminals. Digital input sources are not

output. If no sound is heard when an input source is selected,

verify that the source is connected to an analog input.

•

You cannot select different AM or FM radio stations for your

main room and Zone 2/3. The same AM/FM radio station will be

heard in each room. Namely, if you have selected an FM station

for the main room, that station will also be output in Zone 2/3.

•

When you have selected

NET

USB

as input selector, the last

selector selected will be set for Main room and Zone 2/3.

•

When Zone 2/3 is activated and its input selector is selected, the

power consumption of standby mode slightly increases.

•

While Zone 2/3 is on,

functions will not work.

•

When setting the AV receiver to standby mode while Zone 2/3 is

active, the

indicator is dimly lit.

•

Activating Zones in the main room when the listening mode is set

to Pure Audio will automatically switch it to Direct.

•“

GAME2

” cannot be selected as input sources for Zone 2/3.

•

When “

GAME2

” is the input source of Main room and Zone 2/3

is set to share the same source, no sound will be output from

Zone 2/3.

•

Even if you repeatedly press the remote controller’s

ZONE

select zones, the last zone selection will be retained once you

have switched to other components by pressing other

REMOTE

MODE

after pressing

ZONE

To select an input source for Zone 2/3, press

ZONE

repeatedly, followed by an

INPUT SELECTOR

button.

To select AM or FM, press the

TUNER

input selector

and

ZONE

repeatedly.

To turn off Zone 2/3, press

ZONE

repeatedly,

followed by

RECEIVER

The zone is turned off.

Tip

•

The corresponding trigger output goes low (0 volts).

Press

ZONE

repeatedly.

Use

VOL

Press

ZONE 2

ZONE 3

(the Z2/Z3 indicator on

the AV receiver’s display flashes).

Use

MASTER VOLUME

control within 8 seconds.

Press

ZONE

repeatedly, and then press

MUTING