Onkyo TX SR607 Owner Manual - Page 43

Speaker Settings - bi amp

Get Onkyo TX SR607 - AV Receiver PDF manuals and user guides
UPC - 751398008719
View all Onkyo TX SR607 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

First Time Setup-Continued Speaker Settings 4 If you change these settings, you must run the Audyssey 2EQ™ Room Correction and Speaker Setup again (see page 46). If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you've connected your front speakers to the FRONT L/R and SURR BACK L/R terminal posts for bi-amping, you must change the "Speaker Type" setting. For hookup information, see "Bi-amping the Front Speakers" on page 19. 5 Notes: • When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room. • Before you change these settings, turn down the volume. 1 Press the [RECEIVER] button, followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. Use the Up and Down [R]/[X] buttons to select "Speaker Impedance", and then use the Left and Right [F]/[S] buttons to select: 4ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6ohms: Select if the impedances of all speakers are between 6 and 16 ohms. Note: North American/Taiwan models do not support speakers with an impedance of less than 6 ohms. Use the Up and Down [R]/[X] buttons to select "Speaker Type", and then use the Left and Right [F]/[S] buttons to select: Normal: Select this if you've con- nected your front speakers normally. Bi-Amp:Select this if you've connected your front speakers for bi-amped operation. Note: Powered Zone 2 cannot be used if "Speaker Type" is set to "Bi-Amp". 6 Use the Up and Down [R]/[X] but- tons to select "Surr Back/Front 2 Use the Up and Down [R]/[X] but- tons to select "2. Speaker High", and then use the Left and Right [F]/[S] buttons to select: Setup", and then press [ENTER]. Front High: The "Speaker Setup" menu appears. FRONT HIGH L/R speakers can be used. 2. Speaker Setup 1. Speaker Settings 2. Speaker Configuration 3. Speaker Distance 4. Level Calibration 5. Equalizer Settings Surr Back: SURR BACK L/R speakers can be used. Note: • If the "Speaker Type" setting is set to "Bi-Amp", or Powered Zone 2 is set to "Not Act", this setting cannot be 3 Use the Up and Down [R]/[X] but- selected. tons to select "1. Speaker Set- 7 Press the [SETUP] button. tings", and then press [ENTER]. The setup menu closes. The "Speaker Settings" menu appears. 2-1. Speaker Settings Speaker Impedance Speaker Type Powered Zone 2 Surr Back/Front High 6ohms Normal Not Act Surr Back Powered Zone 2 See "Zone 2" on page 85. Note: This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
43
First Time Setup
—Continued
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK L/R terminal posts for bi-amping,
you must change the “Speaker Type” setting. For hookup
information, see “Bi-amping the Front Speakers” on
page 19.
Notes:
•
When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
•
Before you change these settings, turn down the
volume.
Powered Zone 2
See “Zone 2” on page 85.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q
]/[
w
] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
3
Use the Up and Down [
q
]/[
w
] but-
tons to select “1. Speaker Set-
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
If you change these settings, you must run the
Audyssey
2EQ™ Room Correction and Speaker Setup
again (see page 46).
2. Speaker Setup
1. Speaker Settings
2. Speaker Configuration
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
2–1. Speaker Settings
Speaker Impedance
Speaker Type
Powered Zone 2
Surr Back/Front High
6ohms
Normal
Not Act
Surr Back
4
Use the Up and Down [
q
]/[
w
] but-
tons to select “Speaker Imped-
ance”, and then use the Left and
Right [
e
]/[
r
] buttons to select:
4ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
6ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
Note:
North American/Taiwan models do not
support speakers with an impedance of
less than 6 ohms.
5
Use the Up and Down [
q
]/[
w
] but-
tons to select “Speaker Type”,
and then use the Left and Right
[
e
]/[
r
] buttons to select:
Normal:
Select this if you’ve con-
nected your front speakers
normally.
Bi-Amp:
Select this if you’ve con-
nected your front speakers for
bi-amped operation.
Note:
Powered Zone 2 cannot be used if
“Speaker Type” is set to “Bi-Amp”.
6
Use the Up and Down [
q
]/[
w
] but-
tons to select “Surr Back/Front
High”, and then use the Left and
Right [
e
]/[
r
] buttons to select:
Front High:
FRONT HIGH L/R speakers
can be used.
Surr Back:
SURR BACK L/R speakers
can be used.
Note:
•
If the “Speaker Type” setting is set to
“Bi-Amp”, or Powered Zone 2 is set
to “Not Act”, this setting cannot be
selected.
7
Press the [SETUP] button.
The setup menu closes.