Onkyo TX SR607 Owner Manual - Page 70

Common Procedures in Setup Menu, Speaker Setup, Speaker Settings - subwoofer setup

Get Onkyo TX SR607 - AV Receiver PDF manuals and user guides
UPC - 751398008719
View all Onkyo TX SR607 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Advanced Setup-Continued Common Procedures in Setup Menu ENTER SETUP RECEIVER RXFS 1 Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [R]/[X] buttons to select main menu, and then press [ENTER]. 3 Use the Up and Down [R]/[X] buttons to select the function, and then press [ENTER]. 4 Use the Up and Down [R]/[X] buttons to select setting, and then use the Left and Right [F]/[S] buttons to set them. 5 When you've finished, press the [SETUP] button. The setup menu closes. Speaker Setup Some of the settings in this section are set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function (see page 46). Here you can check the settings made by the Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using the Audyssey 2EQ Room Correction and Speaker Setup function. Note: The Speaker Setup cannot be carried out while headphones are connected to the AV receiver. Speaker Settings See "Speaker Settings" on page 43 Speaker Configuration With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify "Full Band" for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to determine the optimum crossover frequencies. Subwoofer Yes: Select if a subwoofer is connected (default). No: Select if no subwoofer is connected. Front*1 Full Band, 40Hz to 100Hz (default), 120Hz, 150Hz, 200Hz Center*2 Surround*2 Front High*3*4*5*6 Surr Back*3*4*5*7 Full Band, 40Hz to 100Hz, 120Hz, 150Hz, 200Hz None: Select if no speaker is connected. Surr Back CH*8 1ch: Select if only one surround back L speaker is connected. 2ch: Select if two (left and right) surround back speakers are connected (default). 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
70
Advanced Setup
—Continued
Some of the settings in this section are set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup
function (see page 46).
Here you can check the settings made by the Audyssey 2EQ Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the connected speakers after using the Audyssey 2EQ Room Correction
and Speaker Setup function.
Note:
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
Common Procedures in Setup Menu
SETUP
RECEIVER
qwer
ENTER
1
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2
Use the Up and Down [
q
]/[
w
] buttons to
select main menu, and then press
[ENTER].
3
Use the Up and Down [
q
]/[
w
] buttons to
select the function, and then press
[ENTER].
4
Use the Up and Down [
q
]/[
w
] buttons to
select setting, and then use the Left and
Right [
e
]/[
r
] buttons to set them.
5
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
Speaker Setup
Speaker Settings
See “Speaker Settings” on page 43
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify
“Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good
sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be
output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover
frequencies.
Subwoofer
Yes:
Select if a subwoofer is connected (default).
No:
Select if no subwoofer is connected.
Front
*1
Full Band, 40Hz to 100Hz (default), 120Hz, 150Hz, 200Hz
Center
*2
Surround
*2
Front High
*3*4*5*6
Surr Back
*3*4*5*7
Full Band, 40Hz to 100Hz, 120Hz, 150Hz, 200Hz
None:
Select if no speaker is connected.
Surr Back CH
*8
1ch:
Select if only one surround back L speaker is connected.
2ch:
Select if two (left and right) surround back speakers are connected (default).