Onkyo TX-SR706 Owner Manual - Page 55

Using the Multichannel DVD Input, Adjusting the Bass & Treble, Displaying Source Information - tx 7 1 thx

Get Onkyo TX-SR706 - AV Receiver PDF manuals and user guides
UPC - 751398008214
View all Onkyo TX-SR706 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Basic Operations-Continued Using the Multichannel DVD Input The multichannel DVD input is for connecting a component with a 7.1-channel analog audio output, such as a DVD-Audio or SACD-capable DVD player, or an MPEG decoder. See page 27 for hookup information. Remote controller Press the [MULTI CH] button. "Multich" appears on the display. Audio from the multichannel DVD input will now be used for the DVD input source. Notes: • While the multichannel DVD input is selected, the Speaker Configuration settings on page 73 are ignored, and signals from the multichannel input are fed to the speakers as they are. • The multichannel DVD input cannot be used if "Speakers Type" is set to "Bi-Amp" (see page 45). • This procedure can also be performed on the AV receiver/AV amplifier by using its [MULTI CH] button. Adjusting the Bass & Treble You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio or THX listening mode is selected. 1 AV receiver/ AV amplifier Press the [TONE] button repeatedly to select either "Bass" or "Treble". 2 Use the TONE [-]/[+] buttons to adjust. ■ Bass You can boost or cut low-frequency sounds output by the front speakers from -10 dB to +10 dB in 2 dB steps. ■ Treble You can boost or cut high-frequency sounds output by the front speakers from -10 dB to +10 dB in 2 dB steps. Notes: • This setting is not available when the multichannel DVD input is selected. • This procedure can also be performed on the remote controller by using [AUDIO] button (see page 83). Displaying Source Information You can display various information about the current input source as follows. Remote controller Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. Note: This procedure can also be performed on the AV receiver/AV amplifier by using its [DISPLAY] button. The following information can typically be displayed for input sources. Input source Listening mode Signal format* Sampling frequency * If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format and the number of channels is displayed. For some digital input signals, including multichannel PCM, the signal format, number of channels, and sampling frequency is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Setting the Display Brightness You can adjust the brightness of the AV receiver/AV amplifier's display. Remote controller Press the [RECEIVER] button, and then press the [DIMMER] button repeatedly to select: • Normal + VOLUME light on. • Normal + VOLUME light off. • Dim + VOLUME light off. • Dimmer + VOLUME light off. Alternatively, you can use the AV receiver/AV amplifier's [DIMMER] button (North American models and TX-SA706 only). 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
55
Basic Operations
—Continued
The multichannel DVD input is for connecting a compo-
nent with a 7.1-channel analog audio output, such as a
DVD-Audio or SACD-capable DVD player, or an
MPEG decoder. See page 27 for hookup information.
Notes:
•
While the multichannel DVD input is selected, the
Speaker Configuration settings on page 73 are
ignored, and signals from the multichannel input are
fed to the speakers as they are.
•
The multichannel DVD input cannot be used if
“Speakers Type” is set to “Bi-Amp” (see page 45).
•
This procedure can also be performed on the AV
receiver/AV amplifier by using its [MULTI CH] but-
ton.
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio or THX listening
mode is selected.
■
Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■
Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
Notes:
•
This setting is not available when the multichannel
DVD input is selected.
•
This procedure can also be performed on the remote
controller by using [AUDIO] button (see page 83).
You can display various information about the current
input source as follows.
Note:
This procedure can also be performed on the AV
receiver/AV amplifier by using its [DISPLAY] button.
The following information can typically be displayed for
input sources.
*
If the input signal is analog, no format information is displayed.
If the input signal is PCM, the sampling frequency is displayed.
If the input signal is digital but not PCM, the signal format and
the number of channels is displayed. For some digital input sig-
nals, including multichannel PCM, the signal format, number of
channels, and sampling frequency is displayed.
Information is displayed for about three seconds, then the previ-
ously displayed information reappears.
You can adjust the brightness of the AV receiver/AV
amplifier’s display.
Using the Multichannel DVD Input
Remote
controller
Press the [MULTI CH] button.
“Multich” appears on the display.
Audio from the multichannel DVD
input will now be used for the DVD
input source.
Adjusting the Bass & Treble
1
AV receiver/
AV amplifier
Press the [TONE] button repeat-
edly to select either “Bass” or
“Treble”.
2
Use the TONE [–]/[+] buttons to
adjust.
Displaying Source Information
Remote
controller
Press the [RECEIVER] button,
and then press the [DISPLAY]
button repeatedly to cycle
through the available informa-
tion.
Setting the Display Brightness
Remote
controller
Press the [RECEIVER] button,
and then press the [DIMMER]
button repeatedly to select:
•
Normal + VOLUME light on.
•
Normal + VOLUME light off.
•
Dim + VOLUME light off.
•
Dimmer + VOLUME light off.
Alternatively, you can use the AV
receiver/AV amplifier’s [DIMMER]
button (North American models and
TX-SA706 only).
Sampling
frequency
Input source
Signal format*
Listening
mode