Onkyo TX-SV727 Owner Manual - Page 43

NOTE: The tuning steps by which the tuned frequency changes on each band have been set at the factory to the proper value for the country where each unit is to be sold. If you use the unit in a country where a different tuning step is required or if the broadcast frequencies in your country change so that you can not tune in radio stations precisely, contact your authorized ONKYO Service Center. This device employs a microcomputer to perform various functions and operations. If interference generated by an external power supply, radio waves, or other electrical source results in an accident which causes the specified operations and functions to operate abnormally. To perform a reset, please follow the procedure below. 1. Press and hold down the VIDEO-1 button, then press the POWER button. 2. After "clear" is displayed, the preset memory and parameters stored in the memory, such as surround, are initialized and will return to the factory settings. Problem with the RC-288M remote control If the remote control does not operate, • First, try operations using the buttons of the main unit for each function. If operation is not possible, the fault is in the main unit and not the remote control. • If the batteries are weak, replace the batteries. The buttons of this remote control cannot be memorized or some remote control functions cannot be memorized. • This remote control uses an infrared ray system and most functions can be memorized. However, there may some instances where memorization is not possible or some remote control functions cannot be memorized due to the nutput miathori. It is difficult to memorize functions using the buttons of this remote control, and even when a function has been memorized, operation is incorrect. • The RC-288M is not aimed directly at the other remote control, or the distance between the two units is out of range. Confirm that these two factors are correct. • Confirm whether the batteries of your existing remote control are weak. (If the batteries are weak, it may be impossible to operate a function or to memorize functions. Insert new batteries and try again.) • The RC-288M remote control uses an infrared ray system and most functions can be memorized. However, there may be some instances where memorization is not possible or some remote control functions cannot be memorized due to the output method of the other remote control. The functions of the television, video, etc., memorized into this remote control do not operate properly with the buttons. • Make sure the functions memorized correspond to the characters or marks on the buttons. The functions will operate as memorized, without relation to the characters or marks on the button. • If the batteries are weak, it may be impossible to memorize functions. Insert the indicated type of batteries into your existing remote control and into this remote control, and •try memorizing the code once again. (Make sure the new batteries are the correct type indicated for the equipment.) If the operable distance of the RC-288M is shorter than that of the existing remote control, or if the reaction time of the machine is slow when using the RC-288M. • The operable distance of this remote control and your existing remote control are different. In this case, it may happen that the operable distance is shortened. • Try memorizing once again, making sure you are memorizing at an appro- priate distance. • Check that the batteries are not weak. • It may be simply that the correspondence between the unit and machine is slow. The codes memorized by the button of RC-288M have been "for- a If the batteries are taken nut of the unit for more than one hour, memorized gotten". codes will be lost. In this case, please memorize the codes once again. Questions Q : How do I get my remote speaker to turn on? Q : I cannot get On-screen graphics on my TV/ Monitor. Q : How do I get just my TV sound through my stereo? Q :Why is there no sound coming from my unit? It worked fine yesterday and there is some music faintly in the background. Answers A : Hit multi-source button, select a source (CD, FM) then hit remote speaker button. On hand held remote, hit VOLUME •/V key to send volume to remote speakers. This is independent from the main volume. A : Make sure you have a single RCA video cable running from the monitor out on the back of the ONKYO going to the EXT. 1 or video-1 input of your TV/Monitor. You must make the input selection at the TV/Monitor. (Many customer assume that the ONKYO will switch the TV/Monitor mode automatically). A : On the back of your TV/Monitor you should see AUDIO OUT LEFT and RIGHT RCA jacks. Run a standard RCA cable from those outputs to any line level input on the ONKYO. Do not use the Phono input. A : Check to see that the tape 2 monitor button is not engaged. 43