Optoma ZU725TST Manual - Page 65

Accessing the web control panel, Communication > Network Setup > IP Address

Get Optoma ZU725TST PDF manuals and user guides View all Optoma ZU725TST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

USING THE PROJECTOR Accessing the web control panel When network is available, connect the projector and the computer to the same network. Use the projector address as the web URL to open the web control panel in a browser. 1. Check the projector address using the OSD menu. ‡ On a wired network, select Communication > Network Setup > IP Address. Note: Make sure DHCP is enabled. 2. Open a web browser and type the projector address in the address bar. 3. The web page redirects to the web control panel. 4. In the Username field, type the username: admin (default) In the Password field, type the password.: Device serial number (default). Path: Menu -> Information -> Device -> Serial Number. Note: It is needed to change the username and password once you have logged in. It is also advised to use a strong password. When network is not available, refer to "Directly connect the projector to a computer" section. Directly connect the projector to a computer When network is not available, connect the projector to the computer directly using a RJ-45 cable, and configure the network settings manually. RJ-45 Cable 1. Assign IP address to the projector ‡ From the OSD menu, select Network Setup > DHCP. ‡ Turn off DHCP, and manually set the projector's IP Address, Subnet Mask, and Gateway. ‡ Press Enter to confirm the settings. 2. Assign IP address to the computer ‡ Set the Default Gateway and Subnet Mask of the computer to match the projector. ‡ Set the IP address of the computer to match the first three numbers of the projector. For example, if the projector IP address is 192.168.000.100, set the computer IP address to 192.168.000.xxx, where xxx is not 100. 3. Open a web browser and type the projector address in the address bar. 4. The web page redirects to the web control panel. English 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
English
65
USING THE PROJECTOR
Accessing the web control panel
When network is available, connect the projector and the computer to the same network. Use the projector
address as the web URL to open the web control panel in a browser.
1.
Check the projector address using the OSD menu.
±
On a wired network, select
Communication > Network Setup > IP Address
.
Note:
Make sure DHCP is enabled.
2.
Open a web browser and type the projector address in the address bar.
3.
The web page redirects to the web control panel.
4.
In the Username field, type the username: admin (default) In the Password field, type the password.:
Device serial number (default). Path: Menu -> Information -> Device -> Serial Number.
Note:
It is needed to change the username and password once you have logged in. It is also advised
to use a strong password.
When network is not available, refer to “Directly connect the projector to a computer” section.
Directly connect the projector to a computer
When network is not available, connect the projector to the computer directly using a RJ-45 cable, and
configure the network settings manually.
RJ-45 Cable
1.
Assign IP address to the projector
±
From the OSD menu, select
Network Setup > DHCP
.
±
Turn off DHCP, and manually set the projector’s IP Address, Subnet Mask, and Gateway.
±
Press
Enter
to confirm the settings.
2.
Assign IP address to the computer
±
Set the Default Gateway and Subnet Mask of the computer to match the projector.
±
Set the IP address of the computer to match the first three numbers of the projector.
For example, if the projector IP address is 192.168.000.100, set the computer IP address to
192.168.000.xxx, where xxx is not 100.
3.
Open a web browser and type the projector address in the address bar.
4.
The web page redirects to the web control panel.