Optoma ZU725TST Manual - Page 79

Manual Warp Control Instruction, Magenta, Red

Get Optoma ZU725TST PDF manuals and user guides View all Optoma ZU725TST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

ADDITIONAL INFORMATION Manual Warp Control Instruction 1. The Warp/Blend control option needs to be switched to the OSD option. Steps: Menu -> Display -> Geometric Correction -> Warp Control -> Advanced. 2. Changing the grid color can help to distinguish between grid color lines on each projector when completing the warping adjustment. The Warp/Blend grid color options include: Green (default), Magenta, Red, and Cyan. Steps: Menu -> Display -> Geometric Correction -> Advanced Warp -> Grid Color. 3. Set Blend overlap size. Steps: Menu -> Display -> Geometric Correction -> Advanced Warp -> Blend Setting -> Blend Width. The options and effective range of overlap size as follows: (a) Left: 0 (0%) / 192 (10%) ~ 960 (50%) (b) Right: 0 (0%) / 192 (10%) ~ 960 (50%) (c) Top: 0 (0%) / 120 (10%) ~ 600 (50%) (d) Bottom: 0 (0%) / 120 (10%) ~ 600 (50%) 3.1 Setup projectors and then set the overlap size according to the actual projection overlap. A. Make sure the overlap size for is smaller than the overlap size of actual projection. B. Turning on the blend width screen for all the projectors helps determine the effective overlap range. See below for settings for a 1x2 layout as an example, and follow the steps below: 3.2 Adjust the overlap size of right boundary of left projector first. A. The left side of the overlap area will shift along with the values of the blend setting. Overlap area is shown by a square with light color. B. Adjust overlap size until the left side of overlap area of left projector does not exceed the left boundary of right projector. English 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
English
79
ADDITIONAL INFORMATION
Manual Warp Control Instruction
1.
The Warp/Blend control option needs to be switched to the OSD option.
Steps: Menu -> Display ->
Geometric Correction -> Warp Control -> Advanced.
2.
Changing the grid color can help to distinguish between grid color lines on each projector when
completing the warping adjustment. The Warp/Blend grid color options include: Green (default),
Magenta, Red, and Cyan. Steps: Menu -> Display -> Geometric Correction -> Advanced Warp -> Grid
Color.
3.
Set Blend overlap size. Steps: Menu -> Display -> Geometric Correction -> Advanced Warp -> Blend
Setting -> Blend Width. The options and effective range of overlap size as follows:
(a)
Left: 0 (0%) / 192 (10%) ~ 960 (50%)
(b)
Right: 0 (0%) / 192 (10%) ~ 960 (50%)
(c)
Top: 0 (0%) / 120 (10%) ~ 600 (50%)
(d)
Bottom: 0 (0%) / 120 (10%) ~ 600 (50%)
3.1
Setup projectors and then set the overlap size according to the actual projection overlap.
A.
Make sure the overlap size for is smaller than the overlap size of actual projection.
B.
Turning on the blend width screen for all the projectors helps determine the effective overlap
range.
See below for settings for a 1x2 layout as an example, and follow the steps below:
3.2
Adjust the overlap size of right boundary of left projector first.
A.
The left side of the overlap area will shift along with the values of the blend setting. Overlap
area is shown by a square with light color.
B.
Adjust overlap size until the left side of overlap area of left projector does not exceed the left
boundary of right projector.