Panasonic AJD455 AJD455 User Guide - Page 51

Specifications GENERAL Power supply: AC 120 V, 50 - 60 Hz Power consumption: 95 W Operating ambient temperature: 41°F to 104°F (5°C to 40°C) Operating ambient humidity: 10% to 90% (no condensation) Weight: Dimensions (W × H × D): 31.46 lbs (14.3 kg) 16-3/4 × 6-15/16 ×16-3/8 inches Recording format: (424 × 175.2 × 415 mm) DVCPRO format/DV format Recording video signals: 525i Recording audio signals: 48 kHz, 16 bits, 2 channels (DVCPRO) Recording tracks: Digital video/audio helical track Time code; Recorded in sub-code area Digital audio; 2 channels Cue Track; 1 track Control (CTL); 1 track Tape speed: 33.820 mm/sec Recording time: 126 minutes (with AJ-P126LP) 66 minutes (with AJ-P66MP) Tape: 1/4-inch thin magnetic layer metal tape FF/REW time: Less than 3 min (with AJ-P126LP) Less than 2 min (with AJ-P66MP) Editing accuracy: Tape timer accuracy: Servo lock time: ±0 frame (using time code) ±1 frame (using continuous CTL signal) Less than 0.5 sec. (color framing/ standby ON) VIDEO (Digital video) Sampling frequencies: Quantizing: Video compression system: Video compression ratio: Error correction: Video recording/playback bit rate: Samples × number of effective lines: Y; 13.5 MHz/PB, PR; 3.375 MHz 8 bits DV-based compression (SMPTE314M) 1/5 (DVCPRO) Reed-Solomon product code 25 Mbps (DVCPRO) 720 × 480/frame (DVCPRO) (Digital IN/Analog component OUT) Video bandwidth: Y; 30 Hz to 5.5 MHz (±1.0 dB) S/N ratio: K factor: PB, PR; 30 Hz to 1.3 MHz (±1.0 dB) Better than 56 dB Less than 2% (Analog component IN/Analog component OUT) Video bandwidth: Y; 30 Hz to 5.5 MHz (-1.5 dB to +1.0 dB) PB, PR; 30 Hz to 1.3 MHz S/N ratio: K factor: (-2.0 dB to +1.0 dB) Better than 55 dB Less than 2% (Analog composite IN/Analog composite OUT) Video bandwidth: DG: DP: Y/C delay: K factor: S/N ratio: Y; 30 Hz to 4.5 MHz (-1.5 dB to +1.0 dB) Less than 4% Less than 3° Better than 20 ns Less than 3% Better than 48 dB (Video input connector) Analog component input: Analog composite input: S1 VIDEO input: Reference input: Serial digital component input (option): BNC×3 (Y, PB, PR) Y; 1.0 Vp-p, 75Ω PB, PR; 0.486/0.7 Vp-p switchable, 75Ω (75% color bar, 7.5% setup) BNC×2, loop-through, 75Ω on/off S terminal (4-pin)×1 Y; 1.0 Vp-p, 75Ω C; 0.286 Vp-p (burst), 75Ω Analog composite BNC×2, loop-through, 75Ω on/off Complies with SMPTE259M-C standard, BNC×2, active through (Video output connector) Analog component output: BNC×3 (Y, PB, PR) Y; 1.0 Vp-p, 75Ω PB, PR; 0.486/0.7 Vp-p switchable, 75Ω (75% color bar, 7.5% setup) Analog composite output: BNC×3 Video1/video2/video3 (superimpose on/off) S1 VIDEO output: S terminal (4-pin)×1 Y; 1.0 Vp-p, 75Ω C; 0.286 Vp-p (burst), 75Ω Serial digital component output (option): Complies with SMPTE259M-C standard, BNC×3 (Video output signals adjustment) Video gain: ±3 dB Chroma gain: ±3 dB Hue: ±30° Setup: ±14 IRE Sync phase: ±15 µs SC phase: ±180° AUDIO (Digital audio) Sampling frequencies: Quantizing: Frequency response: Dynamic range: Distortion: Crosstalk: Wow & flutter: Headroom: De-emphasis: 48 kHz (synchronized with video signal) 16 bits 20 Hz to 20 kHz (±1.0 dB) (at reference level) Better than 85 dB (1 kHz, emphasis OFF, "A" weighted) Less than 0.1% (1 kHz, emphasis OFF, standard level) Less than -80 dB (1 kHz, between 2 channels) Below measurable limits 20 dB T1=50 µs/T2=15 µs (on/off automatic) (Audio input connector) Analog input (CH1/CH2): Digital input (CH1/CH2): Serial digital input (option): XLR×2, 600Ω/high impedance selectable, +4/0/-20/-60 dBu BNC×1, AES/EBU format Complies with SMPTE259M-C, 272M-A standard (BNC, 75Ω) (Audio output connector) Analog output (CH1/CH2): Digital output (CH1/CH2): Serial digital output (option): Monitor output: Headphones: XLR×2, low impedance, +4/0/-20 dBu BNC×1, AES/EBU format Complies with SMPTE259M-C, 272M-A standard (BNC, 75Ω) Phono×1, 600Ω, -8 dBV Variable level, 1/4" phone, 8Ω Other input/output connector Time code input: BNC×1, 0.5 Vp-p to 8 Vp-p, 10 kΩ Time code output: BNC×1, 2.0 Vp-p ±0.5 Vp-p, low impedance RS-422A input/output: D-sub 9-pin, RS-422A interface RS-232C: D-sub 25-pin, RS-232C interface Encoder remote: D-sub 15-pin Digital video interface input/ output (option): Compliant with IEEE1394-1995 standard, 6 pins × 1 Weight and dimensions when shown are approximately. Specifications are subject to change without notice. 51