Panasonic CF-F8 User Manual - Page 25
Troubleshooting Basic/Error Code/Message - boot from cd
View all Panasonic CF-F8 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 25 highlights
Troubleshooting (Basic)/Error Code/Message Troubleshooting Useful Information Getting Started Troubleshooting (Basic) Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the "Reference Manual". For a software problem, refer to the software's instruction manual. If the problem persists, contact your technical support office. You can also check the computer's status in the PC Information Viewer (Î Manual "Check the Computer's Usage Status"). Starting Up and Standby and Hibernation Mode Reference The computer does not power on/ The power indicator or battery indicator is not lit. z Connect the AC adaptor. z Insert a fully charged battery. z Remove the battery pack and the AC adaptor, then connect them again. z If an additional RAM module has been inserted, remove the RAM module and check to see if the RAM module is the recommended one. z When the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact your technical support office. Windows does not start up. z Remove all peripheral devices (e.g. USB memory). z If an additional RAM module has been inserted, remove the RAM module and check to see if the RAM module is the recommended one. z If the power indicator is lit, slide the power switch for four seconds or longer to turn off, then turn on again. z Using the following procedure, start up in Safe Mode, and check the error details. A Turn on the computer, and when the [Panasonic] boot screen disappears (after entering the password*1 if one is set) hold down F8. B Release your finger when [Windows Advanced Options Menu] is displayed, and with Ï or Ð, select [Safe Mode], then press Enter. Follow the on-screen instructions. *1 Supervisor Password or User Password set with the Setup Utility z Press F9 in the Setup Utility (Î page 28 "To start the Setup Utility") to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. Cannot boot from internal CD/DVD drive. z Make sure that the bootable CD/DVD is set properly. z Start the Setup Utility, and confirm the following settings. • [Optical Drive] is set to [Enabled] in the [Advanced] menu. • [Optical Drive Power] is set to [On] in the [Main] menu. • [Boot Option #1] is set to [CD/DVD Drive] in the [Boot] menu. z When an external CD/DVD drive is connected, you cannot boot from the internal CD/ DVD drive. You have forgotten the password. z Supervisor Password or User Password: Contact your technical support office. z Administrator password: • If you have a password reset disk, you can reset the administrator password. Set the disk and enter any wrong password, then follow the on-screen instructions and set a new password. • If you do not have a password reset disk, reinstall (Î Supplementary Instructions for Windows XP) and set up Windows, and then set a new password. "Remove disks or other media. Press any key to restart" or a similar message appears. z A floppy disk is in the floppy disk drive and it does not contain system startup information. Remove the floppy disk and press any key. z This message may appear with some devices connected to the USB port. Remove the device or set [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility. z If the problem persists after removing the disk, it may be a hard disk failure. Perform the reinstallation and return the hard disk to its condition at the time of purchase. (Î Supplementary Instructions for Windows XP) If the problem persists even after the reinstallation, contact your technical support office. [Executing Battery Recali- z The Battery Recalibration was canceled before Windows was shut down last time. To bration] screen appears. start up Windows, turn off the computer by the power switch, and then turn on. The computer will not automatically enter standby/ hibernation. z If you connect to a network using wireless LAN function, perform access point settings. (Î Reference Manual "Wireless LAN") z If you do not use wireless LAN function, turn off wireless LAN function. (Î Reference Manual "Disabling/Enabling Wireless Communication") z Make sure that you are not using any software that regularly accesses the hard disk. When logging on (e.g., resuming the computer), audio is distorted. z Perform the following steps to change the audio settings to prevent audio output. A Click [start] - [Control Panel] - [Sounds, Speech, and Audio Devices] - [Sounds and Audio Devices], and click [Sounds]. B Set [Windows Logon] and [Windows Logoff] to [(None)]. 25 Appendix