Panasonic DMPBD50-MUL DMPBD50-MUL User Guide - Page 32
TV screen and video continued, Sound, HDMI connections, Cannot switch audio.
View all Panasonic DMPBD50-MUL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
TV screen and video (continued) The 4:3 aspect ratio picture expands left and right. Screen size is wrong. ≥Use the television to change the aspect. Refer to your television's operating instructions. ≥When using a component video cable, set "Progressive" to "Video". If the situation is not restored after that, set "TV Aspect" to "4:3 Pan & Scan". There is a lot of after-image when playing video. ≥Turn "3D NR" or "Integrated NR" off if it is on. There is no apparent change in picture quality when adjusted with the "Video" menu in the on-screen menu. ≥The effect is less perceivable with some types of video. The masked-off area is masked ≥If the "Screen Saver Function" in the Setup menu is set to "Off", the masked-off area is in gray. displayed in black. Sound No sound. Low volume. Distorted sound. Cannot hear the desired audio type. ≥Check the connections and the "Digital Audio Output" settings. Check the input mode on the amplifier/receiver if you have connected one. ≥Press [AUDIO] to select the audio. ≥Turn off "V. Surround" in the following cases. - When using discs that do not have surround sound effects such as Karaoke discs. - When playing bilingual broadcast programs. ≥Match the speaker settings with the connected equipment. Change multi channel speaker settings by selecting "Multi Channel" in "Speaker". ≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal. ≥When "BD-Video Secondary Audio" is set to "Off", Dolby Digital Plus, Dolby TrueHD and DTS-HD are output from the DIGITAL AUDIO OUT terminal as Dolby Digital or DTS Digital Surround bitstream. ≥[DivX] Audio may not be output depending on how files were created. Page - 25, 28 25 - 27 6-7, 27 15 25 28 - 17, 27 - Cannot switch audio. ≥There are discs for which audio cannot be changed because of how the disc was created. ≥When connecting an amplifier/receiver using a coaxial cable, optical digital audio cable or an HDMI cable, you cannot switch the audio if "Digital Audio Output" is set to "Bitstream". Set "Digital Audio Output" to "PCM" or connect using audio cables. HDMI connections The images from this unit do not appear on the television. Picture is distorted. Jittering occurs. The 4:3 aspect ratio picture expands left and right. Screen size is wrong. When playing DVD-Video using progressive output, one part of the picture momentarily appears to be doubled up. No sound. Low volume. Distorted sound. Cannot hear the desired audio type. ≥Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to shift to more compatible mode with HDMI equipment. However, Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output the bitstream, select "Restore Default Settings" to restore the factory presets and make proper settings. ≥To output video from a device connected with an HDMI cable, set "HDMI Video Mode" to "On" in the Setup menu. ≥Picture may not be seen when more than 4 devices are connected with HDMI cables. Reduce the number of connected devices. ≥When "24p Output" is set to "On", HDMI authentication takes place where 24p images switch to other images, and a black screen is displayed. ≥When "24p Output" is set to "On", jittering may occur while playing DVD-Video. In this case, turn "24p Output" to "Off". ≥Change "TV Aspect" type to "16:9". ≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting. 1 Connect this unit to the TV with any cable except the HDMI cable. 2 When you connect with the Component Video cable, set "HDMI Video Mode" to "Off" and "Component Video Resolution" to "480i" in the Setup menu. ≥Audio may not be heard when more than 4 devices are connected with HDMI cables. Reduce the number of connected devices. ≥The sound effects will not work when the bitstream signal is output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal. ≥To output audio from a device connected with an HDMI cable, set "HDMI Audio Output" to "On" in the Setup menu. ≥If the sound is distorted when the unit is connected to an amplifier/receiver with an HDMI cable, adjust the settings in "Speaker" in the Setup menu to match the connection. ≥Depending on the connected equipment, the sound may be distorted if this unit is connected with an HDMI cable. ≥When "BD-Video Secondary Audio" is set to "On", Dolby Digital Plus, Dolby TrueHD, and DTS-HD are converted to 48 kHz Dolby Digital and output. LPCM 7.1 channel audio is converted to 5.1 channel audio. In this case, set the "BD-Video Secondary Audio" to "Off". - 7, 8, 27 29 28 - 28 28 28 28 - - 28 28 - 27 RQT9184 (ENG) 32