Panasonic NN-SE284 Installation Instructions

Panasonic NN-SE284 Manual

Get Panasonic NN-SE284 PDF manuals and user guides View all Panasonic NN-SE284 manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic NN-SE284 manual content summary:

  • Panasonic NN-SE284 | Installation Instructions - Page 1
    Panasonic Over The Range Microwave Oven INSTALLATION INSTRUCTIONS Read carefully and keep these installation instructions A REQUIREMENTS FOR INSTALLATION Installation of this product is safest and easiest when performed by two people. Before beginning the installation CAPABLE OF SUPPORTING THE
  • Panasonic NN-SE284 | Installation Instructions - Page 2
    filter. This product is shipped with a standard charcoal filter already installed. The Charcoal Filter cannot be cleaned and should be replaced periodically every your local Panasonic dealer. The part number of the replacement charcoal filter is NN-CF203, refer to the following instructions for
  • Panasonic NN-SE284 | Installation Instructions - Page 3
    PROCEDURE Remove the bracket assembly located on the rear of oven and remove all adhesive tape. STEP 1: PRE-INSTALLATION CHECK POINTS IP3297_F03138Q03CP_Eng_00_101028.indd 3 12" MIN *D 120V AC, min. 15A separated line outlet 30" • Electric range: *D = 30" (76 cm) MINIMUM • Gas range: *D = 323
  • Panasonic NN-SE284 | Installation Instructions - Page 4
    rm the separated line electric outlet. (Fig. 1) 2. Exhaust Preparation: Select the type of ventilation required for your installation, and proceed to the following instructions. a. Top Exhaust (Fig. 1-1) This product is shipped ready for top exhaust ventilation mode use without adjusting the product
  • Panasonic NN-SE284 | Installation Instructions - Page 5
    into the kitchen, the standard charcoal filter is already installed in your oven, ready for recirculating mode. When you replace the charcoal filter, refer to the instructions in the Operating Instructions (Maintenance/Care and Cleaning of Your Microwave Oven). Changing the exhaust direction to the
  • Panasonic NN-SE284 | Installation Instructions - Page 6
    (5) Replace blower cover plate onto the product. Secure blower unit with two screws, one through the blower plate, and the other through oven back plate. Secure blower plate onto the product top with two screws. (Fig. 1-2-4) Blower Unit Mounting Screws Blower Unit Blower Unit Mounting Screws
  • Panasonic NN-SE284 | Installation Instructions - Page 7
    (1) Remove two blower cover plate mounting screws and two blower unit mounting screws, top and rear. (Fig. 1-2-1) (2) Remove the blower cover plate from the product. (Fig. 1-2-1) (3) Carefully lift the blower unit and put it on top of product. (Fig. 1-3-1) Fig. 1-3-1 (4) Use side cutters or tin
  • Panasonic NN-SE284 | Installation Instructions - Page 8
    Blower Plate Back Plate Blower Unit Exhaust Parts Blower Unit Mounting Screws Fig. 1-3-5 Note: Exhaust Adaptor y must be secured onto bracket assembly a before installing it on the wall. See STEP 2: USING THE TEMPLATE for details. 3. EXHAUST DUCT The hood exhaust has been designed to match with
  • Panasonic NN-SE284 | Installation Instructions - Page 9
    these surfaces. A template is provided for preparing these holes. Read the instructions on the template before taping it to the bottom of the cabinet and If there are no wall studs in the opening area, DO NOT install the product. Consult your builder. Note: Cabinets with recessed bottoms sometimes
  • Panasonic NN-SE284 | Installation Instructions - Page 10
    .t in Fig. 2-1) If Rear Exhaust application is chosen, you will need to cut the Rear Exhaust opening. (No.y in Fig. 2-1) STEP 3: INSTALLING THE MOUNTING BRACKET CAUTION: To support the oven's weight, bracket must be secured by at least • Four wood screws on the wall studs (2 screws on each side) or
  • Panasonic NN-SE284 | Installation Instructions - Page 11
    INSTALLATION OF BRACKET 1. Draw a wall stud line. 2. Centre the bracket assembly a against the wall and top cabinet. 3. Drill holes. (Fig. 3-2 or Fig. 3-3) 2 Wall Studs One Wall
  • Panasonic NN-SE284 | Installation Instructions - Page 12
    STEP 4: INSTALLING THE MICROWAVE OVEN 1. Remove contents from inside the oven including glass tray the cabinet. 4. Pass AC cord through kitchen cabinet hole. (No.w in Fig. 2-1) 5. Lift and install the oven onto the bracket by sliding it over the rails of the bracket. This is easily and safely
  • Panasonic NN-SE284 | Installation Instructions - Page 13
    STEP 5: INSTALLING THE EXHAUST ADAPTOR AND AIR FILTER Note: If Top Exhaust application is chosen, Mount Exhaust Adaptor follow step 1-3 below. Remove 2 screws from the top plate. 1.
  • Panasonic NN-SE284 | Installation Instructions - Page 14
    the filter.) 7. Confirm the outdoor exhaust flapper has opened. 8. Set the microwave oven for 1 minute and confirm the oven is operating normally using a cup of water. 9. Keep these installation instructions for the local electrical inspector's use. IP3297_F03138Q03CP_Eng_00_101028.indd 14 14 2010-10
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
1
Panasonic Over The Range Microwave Oven
INSTALLATION INSTRUCTIONS
Read carefully and keep these installation instructions
A REQUIREMENTS FOR INSTALLATION
Installation of this product is safest and easiest when performed by two people. Before beginning the
installation, please read the following requirements to make sure you have everything you need to safely
install this product.
1. SUPPLY CIRCUIT AND GROUNDING REQUIREMENTS
This oven must be plugged into a 15 AMP or 20 AMP, 120 volt, 60 Hz, 3 prong grounded outlet. The outlet
must be connected to a separate 15 AMP or 20 AMP circuit of the proper voltage and frequency. No other
appliance should share the circuit. Wire size must conform to the requirements of the National Electric Code
or the prevailing local code for this kilowatt rating.
The recommended location for this outlet is inside the cabinet directly above where the oven is going to be
installed. This location is desirable because the power supply cord on the product is short. If an outlet is
not readily available, one should be installed by a quali
fi
ed electrician and should conform to the National
Electric Code or the prevailing local code.
The installer must perform a ground continuity check on the outlet box to ensure that it is properly
grounded, and if it does not meet the electrical requirements of the product a quali
fi
ed electrician should be
employed to correct any de
fi
ciencies.
2. MOUNTING SURFACE WEIGHT CAPACITY REQUIREMENTS
FOR PERSONAL SAFETY, ANY MOUNTING SURFACE FOR THIS PRODUCT MUST BE CAPABLE OF
SUPPORTING THE PRODUCT’S WEIGHT OF 55 lbs. (25 kg). PLUS ADDITIONAL OVEN LOADS OF UP
TO 22 lbs. (10 kg). FOR A TOTAL WEIGHT OF 77 lbs. (35 kg).
Proper installation of this product requires that the product be partially supported by the bottom surface of
the cabinet directly above the mounting location. Therefore reinforcing this bottom might be necessary if the
cabinet cannot support the weight requirement mentioned above.
3. MOUNTING SPACE REQUIREMENT
Kitchen cabinet depth must be at least 12" (30.5 cm) and not
over 13" (33 cm).
A minimum width of 30" (76 cm) is required on a
fl
at, vertical
wall for installation of this product.
This product is suitable for use above gas or electric cooking
equipment 36 in. or less. To reduce the risk of
fi
re or electric
shock, install the oven at the clearance "H" speci
fi
ed below:
(Fig. A-1)
•
Electric range:
H = 13
5
/
8
" (34.6 cm) MINIMUM
•
Gas range:
H = 16" (40.6 cm) MINIMUM
H
30"
(76 cm)
Fig. A-1
F03138Q03CP
IP0109-51110
Printed in China
IP3297_F03138Q03CP_Eng_00_101028.indd 1
IP3297_F03138Q03CP_Eng_00_101028.indd
1
2010-10-28 11:51:29
2010-10-28
11:51:29