Panasonic PT-50LC13 Multi-media Display - Page 7

Accessories, Remote Control Battery Installation

Get Panasonic PT-50LC13 - 50inch Rear Projection TV PDF manuals and user guides
UPC - 037988974924
View all Panasonic PT-50LC13 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Getting Started Accessories 1. Remote Control 2. Batteries 2 "AA" 3. RGB Cable (2 m) 4. DVI Cable (2 m) (EUR7603ZB0) (LSJA0239-1 or LSJA0443) (K1HA24DA0003) Before Using Remote Control Battery Installation Requires two AA batteries (supplied). 1. Turn the Transmitter face down. Remove top cover by pressing down on marking and sliding cover off in the direction indicated. 2. Install the batteries as shown in the battery compartment. (Polarity + or - must match the markings in the compartment). 3. Replace the cover and slide in reverse until the lock snaps. Two AA size CAUTION Incorrect battery installation can cause the batteries to leak, leading to personal injury and/or damage to the remote control. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). 3. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 4. Battery replacement is necessary when the remote control acts sporadically or stops operating the projection display set. Helpful Hints: (1) For frequent remote control users, replace old batteries with Alkaline batteries for longer battery life. (2) Whenever you remove the batteries, you may need to reset the remote control infrared codes. We recommend that you record the code on page 70, prior to setting up the remote. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
7
Getting Started
Accessories
Requires two AA batteries (supplied).
1.
Turn the Transmitter face down.
Remove top cover by pressing
down on marking and sliding
cover off in the direction indicated.
2.
Install the batteries as shown in
the battery compartment.
(Polarity + or - must match the
markings in the compartment).
3.
Replace the cover and slide
in reverse until the lock
snaps.
Incorrect battery installation can cause the batteries to leak, leading to personal injury and/or damage to the remote
control.
Observe the following precautions:
1.
Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2.
Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
3.
Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
4.
Battery replacement is necessary when the remote control acts sporadically or stops operating the projection
display set.
Two AA size
Remote Control Battery Installation
1. Remote Control
(EUR7603ZB0)
2. Batteries 2 “AA”
3. RGB Cable (2 m)
(LSJA0239-1 or LSJA0443)
4. DVI Cable (2 m)
(K1HA24DA0003)
Before Using
Helpful Hints:
(1) For frequent remote control users, replace old batteries with Alkaline batteries for longer battery life.
(2) Whenever you remove the batteries,
you may need to reset the remote control infrared codes.
We
recommend that you record the code on page 70, prior to setting up the remote.
CAUTION