Panasonic TH-103PB1U Operating Instructions - Page 9

Connections

Page 9 highlights

Connections AC cord connection and ¿xing, cable ¿xing TH-85PB1E TH-103PB1E - AC cord ¿xing Close Unplug the AC cord Push until the hook clicks. Note: Make sure that the AC cord is locked on both the left and right sides. 1 Plug the AC cord into the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper. Open - Cable ¿xing bands Secure any excess cables with bands as required. 2. Pull off. 1. Keep the knob pressed. Unplug the AC cord pressing the two knobs. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ¿rst. Note: Two ¿xing bands are supplied with this unit. In case of securing cables at three (four) positions, please purchase it separately. Pass the attached cable ¿xing band through the clip as shown in the ¿gure. To secure cables connected to Terminals, wrap the cable ¿xing band around them then pass the pointed end through the locking block, as shown in the ¿gure. While ensuring there is suf¿cient slack in cables to minimize stress (especially in the power cord), ¿rmly bind all cables with the supplied ¿xing band. To tighten: To loosen: Push the catch Pull 1 2 Pull 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65

9
Connections
AC cord connection and ±xing, cable ±xing
1
2
Note:
Two ±xing bands are supplied with this unit. In case of securing cables at three (four) positions, please
purchase it separately.
– Cable ±xing bands
Secure any excess cables with bands as required.
Pass the attached cable
±xing band through the
clip as shown in the
±gure.
To secure cables connected to Terminals, wrap the cable ±xing band around them
then pass the pointed end through the locking block, as shown in the ±gure.
While ensuring there is suf±cient slack in cables to minimize stress (especially
in the power cord), ±rmly bind all cables with the supplied ±xing band.
To tighten:
To loosen:
Pull
Pull
Push the catch
Note:
Make sure that the
AC cord is locked on both
the left and right sides.
Push until
the hook clicks.
2.
Pull off.
1.
Keep the
knob pressed.
– AC cord ±xing
TH-85PB1E
TH-103PB1E
Unplug the AC cord
Unplug the
AC cord
pressing the
two knobs.
Note:
When disconnecting the AC
cord, be absolutely sure to
disconnect the AC cord plug
at the socket outlet ±rst.
Close
Open
Plug the AC cord into
the display unit.
Plug the AC cord until
it clicks.
Fix the AC cord with
the clamper.
2
1