Panasonic TH-47LFX6 Operating Instructions - Page 17

Connections

Get Panasonic TH-47LFX6 PDF manuals and user guides View all Panasonic TH-47LFX6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Connections How to remove terminal cover A terminal cover is attached to the input and output terminals to protect them from dust and water. To remove the terminal cover to connect a cable or other item, remove all 12 screws from the terminal cover. Opening the terminal cover with some screws left on will damage the terminal cover. Remove the screws (12) to take out the terminal cover. AC cord connection Notes: • After connection, check the cable is pulled out along the groove without overlapping, then tighten the all 12 screws to attach the terminal cover correctly. Otherwise water enters inside and causes ¿re, electric shock and product damage. • Make sure to read the "Terminal cover" (page iii) section for the correct handling of the terminal cover to use the product properly. Remove the terminal cover (See above) AC cord ¿xing Unplug the AC cord Plug the AC cord into the display unit. Plug the AC cord until it clicks. Note: Make sure that the AC cord is locked on both the left and right sides. Unplug the AC cord pressing the two knobs. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ¿rst. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
9
How to remove terminal cover
AC cord connection
Connections
Notes:
• After connection, check the cable is pulled out along the groove without overlapping, then tighten the all 12 screws
to attach the terminal cover correctly. Otherwise water enters inside and causes
¿
re, electric shock and product
damage.
• Make sure to read the “Terminal cover” (page iii) section for the correct handling of the terminal cover to use the
product properly.
A terminal cover is attached to the input and output terminals to protect them from dust and water.
To remove the terminal cover to connect a cable or other item, remove all 12 screws from the terminal cover.
Opening the terminal cover with some screws left on will damage the terminal cover.
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
Make sure that the AC cord is locked on both the left
and right sides.
Unplug the AC cord
Unplug the AC cord pressing the two knobs.
Note:
When disconnecting the AC cord, be absolutely
sure to disconnect the AC cord plug at the
socket outlet
¿
rst.
AC cord
¿
xing
Remove the screws (12) to
take out the terminal cover.
Remove the terminal
cover
(See above)