Panasonic WV-CS954 Operating Instructions - Page 15

Camera Installation

Get Panasonic WV-CS954 PDF manuals and user guides View all Panasonic WV-CS954 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

CAMERA INSTALLATION ■ Preparing the Camera and Decorative Cover for Side Cable Exit The camera and decorative cover should be prepared as shown below when mounting the camera on a ceiling or wall with its cables (power, video output, RS485, alarm in, alarm out) exiting from the side. The camera mounting base needs to be removed in order to prepare the camera. See steps 1 and 2 below for information about how to remove the camera mounting base. * Prevent the dome cover from being scratched by placing it on a soft cloth while you are working. Preparing the Camera Die Cast Case* Break it off with a pair of pliers. 2. Rotate the camera base unit in the direction indicated by the arrow and remove it. Rotate 15° Pull the camera mounting base up to remove it. 3. Using the camera mounting base as a template, mark the locations of the four mounting holes on the ceiling. If you are using the top cable exit configuration, mark the location of the cable hole on the ceiling and drill the hole. Preparing the Decorative Cover Cut it off with a razor knife. ■ Installing the Camera • Select an installation location that is strong enough to withstand the total weight of the camera. Installing the camera at a location that is too weak can cause it to fall. • Remove the protection sheet after the installation work is complete. • If you are using an optional bracket to install the camera, install the bracket in accordance with the instructions that come with it. 1. Remove the fixing screw (M3 × 6) that secures the camera to the mounting base. Put the screw in a place where it will not become lost. Mark here 4. Affix the camera mounting base onto the ceiling. Use screws (M4) at the locations you marked above to secure the mounting base to the ceiling. If you do not plan to install the camera right away, affix the dust protection sheet that comes with the camera to the mounting base to keep dust off of it. Screws (M4, available separately) Dust Protection Sheet (comes with camera) Fixing screw After loosening the screw, press upwards on the camera and then remove it. -15-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
CAMERA INSTALLATION
■
Preparing the Camera and
Decorative Cover for Side Cable
Exit
The camera and decorative cover should be prepared
as shown below when mounting the camera on a
ceiling or wall with its cables (power, video output,
RS485, alarm in, alarm out) exiting from the side.
The camera mounting base needs to be removed in
order to prepare the camera. See steps 1 and 2 below
for information about how to remove the camera
mounting base.
* Prevent the dome cover from being scratched by
placing it on a soft cloth while you are working.
■
Installing the Camera
• Select an installation location that is strong enough
to withstand the total weight of the camera.
Installing the camera at a location that is too weak
can cause it to fall.
• Remove the protection sheet after the installation
work is complete.
• If you are using an optional bracket to install the
camera, install the bracket in accordance with the
instructions that come with it.
1. Remove the fixing screw (M3
×
6) that secures the
camera to the mounting base.
Put the screw in a place where it will not become
lost.
2. Rotate the camera base unit in the direction
indicated by the arrow and remove it.
3. Using the camera mounting base as a template,
mark the locations of the four mounting holes on the
ceiling.
If you are using the top cable exit configuration,
mark the location of the cable hole on the ceiling
and drill the hole.
4.
Affix the camera mounting base onto the ceiling.
Use screws (M4) at the locations you marked above
to secure the mounting base to the ceiling.
If you do not plan to install the camera right away,
affix the dust protection sheet that comes with the
camera to the mounting base to keep dust off of it.
-15-
Break it off with
a pair of pliers.
Cut it off with
a razor knife.
Preparing the Camera Die Cast Case*
Preparing the Decorative Cover
After loosening
the screw, press
upwards on the
camera and then
remove it.
Fixing screw
Rotate
Pull the camera
mounting base
up to remove it.
15
°
Mark here
Screws
(M4, available separately)
Dust Protection Sheet
(comes with camera)