Panasonic WV-CS954 Operating Instructions - Page 38

3. Move the cursor to ALARM IN 2, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is received by ALARM IN 2. OFF : Ignore alarm input signals. 2POSI : Move to preset position 2. SEQ : Start sequential movement. PATROL2 : Start PATROL 2. PATROL2 (S) : Start PATROL 2, and maintain the stored picture quality settings (page 32) even after completion. AUTOTRACK2 : Move to preset position number 2, and then perform auto tracking. 4. Move the cursor to ALARM IN 3, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is received by ALARM IN 3. OFF : Ignore alarm input signals. 3POSI : Move to preset position 3. SORT : Start sort movement. PATROL3 : Start PATROL 3. PATROL3 (S) : Start PATROL 3, and maintain the stored picture quality settings (page 32) even after completion. AUTOTRACK3 : Move to preset position number 3, and then perform auto tracking. 5. Move the cursor to ALARM IN 4, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is received by ALARM IN 4. OFF : Ignore alarm input signals. 4POSI : Move to preset position 4. BW : Black and white display while signal is being input. PATROL4 : Start PATROL 4. PATROL4 (S) : Start PATROL 4, and maintain the stored picture quality settings (page 32) even after completion. AUTOTRACK4 : Move to preset position number 4, and then perform auto tracking. Notes: • Use PATROL 1 (S) to 4 (S) if you want to switch picture quality (for example to switch picture quality from day to night) when an alarm input is received. ALARM IN4 can be used combined with BW. To use the camera with this application, set the picture quality you want to switch before registering the patrol, then start the patrol registration and then end the registration immediately. • If you want to change the picture quality settings according to alarm input for PATROL 1 (S) to 4 (S), the settings are applied to the camera settings and are kept even after the camera is turned on again. 6. Move the cursor to CNT-CLS 1, and then tilt the joystick left and right to select the alarm output that should be performed over ALARM OUT 1 when an alarm is detected. OFF : No alarm output ALARM : Output an alarm signal when an alarm is detected by the motion detector (page 36) or the preset alarm (page 37). After selecting this setting, perform step 7 to specify the alarm signal output time. AUX1 : Output a contact close signal when AUX1 input is received from the system controller. 7. If you selected ALARM in step 6, move the cursor to TIME OUT and then tilt the joystick left and right to select the alarm signal output time. Tilting the joystick cycles through the output time display in the sequence shown below. (unit: ms) 100 MS ↔ 200 MS ↔ 1000 MS ↔ 2000 MS ↔ 4000 MS Note: The shorter the duration, the more frequent will be the detection output. 8. Move the cursor to CNT-CLS 2, and then tilt the joystick left and right to select the alarm output that should be performed from ALARM OUT 2 when an alarm is detected. OFF : No alarm output BW : Output a contact close signal only while the camera is in the black and white mode. AUX2 : Output a contact close signal when AUX2 input is received from the system controller. Note: It is recommended to set the connected external device to ignore the shorter alarm outputs of 90 ms or less from the camera. 9. Move the cursor to COAX ALM OUT, and then tilt the joystick left or right to toggle it on and off. This setting turns alarm controls whether an alarm is output when the camera moves to one of the preset positions specified for ALARM IN 1 through 4 (1POSI, 2POSI, 3POSI, 4POSI) in steps 2 through 5, above. ON : Output an alarm signal from the video output connector at the point the camera finishes moving to a preset position (number 1 through 4) when there is alarm input to ALARM IN (1 through 4). OFF : No alarm signal output Notes: • The camera ignores alarm inputs during manual operation. • Turn off alarm outputs before downloading or uploading preset data. -38-