Panasonic WV-CS954 Operating Instructions - Page 39

Special Settings

Get Panasonic WV-CS954 PDF manuals and user guides View all Panasonic WV-CS954 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

SPECIAL SETTINGS ■ Using the Special Setup Menu Display the special setup menu from the setup menu to adjust picture quality. First, display the special setup menu. 1. Display the setup menu (page 21), move the cursor to SPECIAL O, and then press the CAM (SET) button. This will display the special setup menu. **SPECIAL SETUP** CHROMA GAIN I•• AP GAIN •••I PEDESTAL ••I HUE ••••I•••• - + PIX OFF REFRESH →PUSH SET CAMERA RESET →PUSH SET SER.NO. BFB03964 RET TOP ● Adjusting Picture Quality Use the following procedure to adjust picture quality. 1. Move the cursor to CHROMA GAIN, and then tilt the joystick left or right to adjust the CHROMA GAIN level. 2. Move the cursor to AP GAIN, and then tilt the joystick left or right to adjust the aperture level. 3. Move the cursor to PEDESTAL, and then tilt the joystick left or right to adjust the PEDESTAL level. 4. Move the cursor to HUE, and then tilt the joystick left or right to adjust the chroma phase (color tone). 5. Move the cursor to PIX OFF O, and then press the CAM (SET) button. This will display the PIX OFF menu. Perform the following steps to perform blemish compensation on the pixels. 6. Select a position that has a blemish with the PIX OFF number, and then press the CAM (SET) button. This will display the blemish compensation pattern setting screen. (1) Use the joystick to move the cross cursor ( ) to the location of the defective pixels. (2) Move the cursor around the display until there are no more white spots (blemishes) visible, and then press the CAM (SET) button. This will store the blemish compensation pattern. (3) This returns to the PIX OFF menu. An asterisk (*) to the right of a PIX OFF number indicates that the number has a blemish compensation pattern assigned to it. ** PIX OFF ** 1* 2* 3* 4* 5* 6* 7* 8 9 10 11 12 13 14 15 16 To delete a blemish compensation pattern (1) On the PIX OFF menu screen, select of the pattern you want to delete, and press the CAM (SET) button. This will display the blemish compensation pattern setting screen. (2) Press the F3 button. (3) This returns to the PIX OFF menu. This will delete the blemish compensation pattern and remove the asterisk (*) to the right of the applicable pattern number. 7. To correct for camera deviation from the preset positions during operation, move the cursor to →PUSH SET to the right of REFRESH, and then press the F3 button. The refresh function corrects the camera position when it starts to deviate from the preset positions. If you are not using the WV-CU650C system controller, perform one of the following steps to correct the camera position. 8. To reset the camera to its initial default settings, move the cursor to →PUSH SET to the right of CAMERA RESET, and then press the F4 button. This resets the camera to it initial factory default settings. Note, however, that this does not change the camera's preset position, AUTO PAN, patrol, RS485, blemish compensation patter and password settings. If you are not using the WV-CU650C system controller, perform one of the following steps to reset the camera. Note: If above operations are performed while the cursor is located at any other item besides CAMERA RESET, further menu operations may become impossible. If this happens, use the procedure under "Displaying the Setup Menu" on page 21 to re-display the menu. 000 000 RET TOP -39-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
SPECIAL SETTINGS
■
Using the Special Setup Menu
Display the special setup menu from the setup menu to
adjust picture quality.
First, display the special setup menu.
1.
Display the setup menu (page 21), move the cursor
to SPECIAL
O
, and then press the CAM (SET)
button.
This will display the special setup menu.
●
Adjusting Picture Quality
Use the following procedure to adjust picture quality.
1. Move the cursor to CHROMA GAIN, and then tilt the
joystick left or right to adjust the CHROMA GAIN level.
2. Move the cursor to AP GAIN, and then tilt the
joystick left or right to adjust the aperture level.
3. Move the cursor to PEDESTAL, and then tilt the
joystick left or right to adjust the PEDESTAL level.
4. Move the cursor to HUE, and then tilt the joystick
left or right to adjust the chroma phase (color tone).
5.
Move the cursor to PIX OFF
O
, and then press the
CAM (SET) button.
This will display the PIX OFF menu. Perform the
following steps to perform blemish compensation
on the pixels.
6. Select a position that has a blemish with the PIX
OFF number, and then press the CAM (SET) button.
This will display the blemish compensation pattern
setting screen.
(1)
Use the joystick to move the cross cursor (
) to
the location of the defective pixels.
(2) Move the cursor around the display until there
are no more white spots (blemishes) visible, and
then press the CAM (SET) button.
This will store the blemish compensation pattern.
(3)
This returns to the PIX OFF menu.
An asterisk (*) to the right of a PIX OFF number
indicates that the number has a blemish
compensation pattern assigned to it.
To delete a blemish compensation pattern
(1) On the PIX OFF menu screen, select of the
pattern you want to delete, and press the CAM
(SET) button.
This will display the blemish compensation
pattern setting screen.
(2)
Press the F3 button.
(3)
This returns to the PIX OFF menu.
This will delete the blemish compensation
pattern and remove the asterisk (*) to the right of
the applicable pattern number.
7. To correct for camera deviation from the preset
positions during operation, move the cursor to
→
PUSH SET to the right of REFRESH, and then
press the F3 button.
The refresh function corrects the camera position
when it starts to deviate from the preset positions. If
you
are
not
using
the
WV-CU650C
system
controller, perform one of the following steps to
correct the camera position.
8. To reset the camera to its initial default settings,
move the cursor to
→
PUSH SET to the right of
CAMERA RESET, and then press the F4 button.
This resets the camera to it initial factory default
settings. Note, however, that this does not change
the camera's preset position, AUTO PAN, patrol,
RS485, blemish compensation patter and password
settings.
If you are not using the WV-CU650C system controller,
perform one of the following steps to reset the camera.
Note:
If above operations are performed while the
cursor is located at any other item besides
CAMERA RESET, further menu operations may
become impossible. If this happens, use the
procedure under "Displaying the Setup Menu" on
page 21 to re-display the menu.
-39-
**SPECIAL SETUP**
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
PIX OFF
REFRESH
→
PUSH SET
CAMERA RESET
→
PUSH SET
SER.NO. BFB03964
RET TOP
••••••
I
••
•••
I
•••••
••
I
••••••
••••
I
••••
-
+
** PIX OFF **
2*
3*
4*
5*
6*
7*
8
9
10
11
12
13
14
15
16
000 000
RET TOP
1*