Philips FWD798 User manual - Page 20

Basic Functions

Page 20 highlights

English Basic Functions Plug and Play (for tuner installation) Plug and play allows you to store all available radio stations automatically. If plug and play has not been installed 1 When you turn on the system,"AUTO INSTALL- PRESS PLAY" will be displayed. 2 Press 38 on the system to start installation. ➜ "INSTALL" will be displayed and followed by "TUNER" and then "AUTO SEARCHING". ➜ PROG will start to flash. ➜ The system will search all radio stations on the FM band, and then the AM band. ➜ All available radio stations with strong signal strength will be stored automatically. ➜ The system will stop searching when all available radio stations are stored or when the memory for 40 preset radio stations is full. ➜ The first preset radio station will play when Plug and Play is completed. Reinstalling plug and play 1 In Standby or demonstration mode, press and hold 38 on the system until "AUTO INSTALL-PRESS PLAY" is displayed. 2 Press 38 again to start installation. ➜ All previously stored radio stations will be replaced. Demonstration mode The system has a demonstration mode that shows various features offered by the system. Activating demonstration ● In Standby mode, press and hold STOP 7 for more than 5 seconds to activate demo mode. ➜ "DEMO ON" is displayed. ➜ Demonstration will begin. Deactivating demonstration ● Press and hold STOP 7 on the system until "DEMO OFF" is displayed. ➜ The system will switch to Standby mode. Note: - If you don't deactivate demostration before switching to Standby mode, the system will enter the demostration mode after 7 seconds. - Even if you remove the AC power cord and reconnect it to the wall socket, the demonstration will remain off until you activate it again. To exit without storing the plug and play ● Press 7 on the system. Notes: - When the power is turned on, the disc tray may open and close to initialise the system. - If Plug and Play installation is not completed, it will be reinitiated the next time you power on the system. - If auto-install is not preset, the system will store the radio station automatically. - If there is no antenna connected,"CHECK ANTENNA" will scroll on the display. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51

20
English
Basic Functions
Plug and Play
(for tuner installation)
Plug and play allows you to store all available
radio stations automatically.
If plug and play has not been installed
1
When you turn on the system, “
AUTO
INSTALL
-
PRESS PLAY
” will be displayed.
2
Press
38
on the system to start installation.
INSTALL
” will be displayed and followed by
TUNER
” and then “
AUTO SEARCHING
”.
PROG
will start to flash.
The system will search all radio stations on
the FM band, and then the AM band.
All available radio stations with strong signal
strength will be stored automatically.
The system will stop searching when all
available radio stations are stored or when the
memory for 40 preset radio stations is full.
The first preset radio station will play when
Plug and Play is completed.
Reinstalling plug and play
1
In Standby or demonstration mode, press and
hold
38
on the system until “
AUTO
INSTALL
-
PRESS PLAY
” is displayed.
2
Press
38
again to start installation.
All previously stored radio stations will be
replaced.
To exit without storing the plug and play
Press
7
on the system.
Notes:
When the power is turned on, the disc tray may
open and close to initialise the system.
If Plug and Play installation is not completed, it
will be reinitiated the next time you power on the
system.
If auto-install is not preset, the system will store
the radio station automatically.
If there is no antenna connected, “
CHECK
ANTENNA
” will scroll on the display.
Demonstration mode
The system has a demonstration mode that
shows various features offered by the system.
Activating demonstration
In Standby mode, press and hold
STOP
7
for
more than 5 seconds to activate demo mode.
DEMO ON
” is displayed.
Demonstration will begin.
Deactivating demonstration
Press and hold
STOP
7
on the system until
DEMO OFF
” is displayed.
The system will switch to Standby mode.
Note:
If you don’t deactivate demostration before
switching to Standby mode, the system will enter
the demostration mode after 7 seconds.
Even if you remove the AC power cord and
reconnect it to the wall socket, the demonstration
will remain off until you activate it again.