Philips FWD798 User manual - Page 21

Preparations

Get Philips FWD798 PDF manuals and user guides View all Philips FWD798 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Preparations English IMPORTANT! - Make sure to complete the preparation procedures before operating the system. Step 1: Inserting batteries into the remote control 3 Step 2: Setting the clock The clock can be set in either 12-hour or 24hour mode ("PM 00:00" or "00:00" for example). 1 The clock can be set in any source mode. ➜ If you have not set the clock,"--:--" will be shown on the display. 1 2 1 Open the battery compartment. 2 Place two batteries (Type R06 or AA) in the compartment with the correct polarity as indicated by "+" and "-" symbols. 3 Close the cover. Using the remote control to operate the system 1 Point the remote control directly at the remote sensor (IR) on the front panel. 2 Select the source you wish to control by pressing one of the source select buttons on the remote control (for example TAPE1/2, TUNER). 3 Then select the desired function (for example 2;, O or P). CAUTION! - Remove batteries if they are exhausted or will not be used for a long time. - Do not use old and new or different types of batteries in combination. - Batteries contain chemical substances, so they should be disposed of properly. 2 Press and hold CLOCK/TIMER until "SELECT CLOCK OR TIMER" is displayed. ➜ Press O or P to change the display to "CLOCK". ➜ Press CLOCK/TIMER again to confirm. 3 Press O or P on the system to set the hours. 4 Press 1 or ¡ on the system to set the minutes. 5 Press CLOCK/TIMER to confirm your setting. The system will store the setting automatically and go back to its previous status. ➜ The time setting becomes effective. Note: - In AUX mode, setting clock using remote control is not possible. To exit the setting without storing (in standby mode) ● Press 9 on the system to exit. ➜ "CANCEL" will appear on the display. ● Press STANDBY ON to exit setting mode and go into POWER ON mode. ● You can also press DISC, DISC1~3, DISC CHANGE, OPEN/CLOSE to exit setting mode and go to disc mode. ● The system will also exit setting mode and go to TUNER,TAPE or AUX mode when you press the corresponding source button. Viewing the clock in any source mode ● When you have set the clock, press CLOCK/ TIMER to view clock. Press DISPLAY on the system to toggle between 12-hour and 24-hour modes. ➜ The time will be displayed for 5 seconds and then the system will go back to its previous status. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
21
English
Preparations
IMPORTANT!
–
Make sure to complete the
preparation procedures before operating
the system.
Step 1:
Inserting batteries into
the remote control
1
Open the battery compartment.
2
Place two batteries (Type R06 or AA) in the
compartment with the correct polarity as
indicated by “+” and “–” symbols.
3
Close the cover.
Using the remote control to operate the
system
1
Point the remote control directly
at the remote sensor (IR) on the
front panel.
2
Select the source you wish to
control by pressing one of the
source select buttons on the
remote control (for example
TAPE1/2, TUNER).
3
Then select the desired function (for example
2;
,
O
or
P
).
CAUTION!
–
Remove batteries if they are
exhausted or will not be used for a long
time.
–
Do not use old and new or different
types of batteries in combination.
–
Batteries contain chemical substances,
so they should be disposed of properly.
Step 2:
Setting the clock
The clock can be set in either 12-hour or 24-
hour mode (“
PM 00
:
00
” or “
00
:
00
” for
example).
1
The clock can be set in any source mode.
➜
If you have not set the clock, “--:--” will be
shown on the display.
2
Press and hold
CLOCK/TIMER
until “
SELECT
CLOCK OR TIMER
” is displayed.
➜
Press
O
or
P
to change the display to
“CLOCK”.
➜
Press
CLOCK/TIMER
again to confirm.
3
Press
O
or
P
on the system to set the
hours.
4
Press
1
or
¡
on the system to set the
minutes.
5
Press
CLOCK/TIMER
to confirm your setting.
The system will store the setting automatically
and go back to its previous status.
➜
The time setting becomes effective.
Note:
–
In AUX mode, setting clock using remote control
is not possible.
To exit the setting without storing (in
standby mode)
●
Press
9
on the system to exit.
➜
“
CANCEL
” will appear on the display.
●
Press
STANDBY ON
to exit setting mode and
go into
POWER ON
mode.
●
You can also press
DISC
,
DISC1~3
,
DISC
CHANGE
,
OPEN/CLOSE
to exit setting
mode and go to disc mode.
●
The system will also exit setting mode and go to
TUNER, TAPE or AUX mode when you press
the corresponding source button.
Viewing the clock in any source mode
●
When you have set the clock, press
CLOCK
/
TIMER
to view clock.
Press
DISPLAY
on the
system to toggle between 12-hour and 24-hour
modes.
➜
The time will be displayed for 5 seconds and
then the system will go back to its previous
status.
1
3
2