Pioneer AVH-P6300BT Owner's Manual - Page 81

DIN Rear-mount, Removing the unit

Get Pioneer AVH-P6300BT PDF manuals and user guides
UPC - 884938122740
View all Pioneer AVH-P6300BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Installation Section 16 Installation 1 1 1 2 1 Side bracket (small) 2 Flush surface screw (5 mm × 6 mm) 2 Install the unit into the dashboard. Insert the mounting sleeve into the dashboard. And then secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. 1 1 Use binding screws (4 mm × 3 mm) only. 2 Tighten two screws on each side. Use any of binding screws (4 mm × 3 mm), binding screws (5 mm × 6 mm) or flush surface screws (5 mm × 6 mm), depending on the shape of screw holes in the bracket. 1 182 53 2 3 4 1 Dashboard 2 Mounting sleeve 3 Side bracket 4 Screw (2 mm × 3 mm) DIN Rear-mount 1 Determine the appropriate position where the holes on the bracket and the side of the unit match. When installing in a shallow space, use the following screw holes. 2 3 1 Screw 2 Dashboard or console 3 Factory radio mounting bracket Note In some types of vehicles, discrepancy may occur between the unit and the dashboard. If this happens, use the supplied frame to fill the gap. Removing the unit Extend top and bottom of the trim ring outwards to remove the trim ring. And then loosen the screws (2 mm × 3 mm) to remove the mounting sleeve. ! When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.) En 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
2
1
1
Side bracket (small)
2
Flush surface screw (5 mm × 6 mm)
2
Install the unit into the dashboard.
Insert the mounting sleeve into the dashboard.
And then secure the mounting sleeve by using
a screwdriver to bend the metal tabs (90°) into
place.
182
53
1
3
4
2
1
Dashboard
2
Mounting sleeve
3
Side bracket
4
Screw (2 mm × 3 mm)
DIN Rear-mount
1
Determine the appropriate position
where the holes on the bracket and the
side of the unit match.
When installing in a shallow space, use the
following screw holes.
1
1
1
Use binding screws (4 mm × 3 mm) only.
2
Tighten two screws on each side.
Use any of binding screws (4 mm × 3 mm),
binding screws (5 mm × 6 mm) or flush sur-
face screws (5 mm × 6 mm), depending on
the shape of screw holes in the bracket.
1
2
3
1
Screw
2
Dashboard or console
3
Factory radio mounting bracket
Note
In some types of vehicles, discrepancy may occur
between the unit and the dashboard. If this hap-
pens, use the supplied frame to fill the gap.
Removing the unit
Extend top and bottom of the trim ring out-
wards to remove the trim ring. And then loos-
en the screws (2 mm × 3 mm) to remove the
mounting sleeve.
!
When reattaching the trim ring, push the
trim ring onto the unit until it clicks. (If the
trim ring is attached upside down, the trim
ring will not fit properly.)
En
81
Section
16
Installation
Installation