Pioneer SC-91 Owner's Manual - Page 47

04 Basic Setup Play ZONE Setup You can select what zone to play when playing via AirPlay and Bluetooth equipped devices as well as when playing audio content on equipment in the home network in DMR mode. ! For playable DLNA-compatible network devices, see page 63 . 1 Select 'Play ZONE Setup' from the Network Option menu. 2 Select the zone in which you want to play the audio contents. 3 When you're finished, press RETURN. You will return to the Network Option menu. Notes ! If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off, then play the audio contents. ! MAIN/HDZONE at ZONE Setup must be set to HDZONE in order to use the HDZONE function (page 98) . Port Number Setting On this receiver, there can be up to 5 numbers of ports where signals are received. 1 Select 'Port Number Setting' from the Network, Bluetooth menu. 2 Select the port number you want to change. 3 Input the port number. ! Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection. ! It is not possible to set the same port number more than once. 4 If there are other port numbers you want to change, repeat steps 2 and 3. Note We recommend setting the port number to 00023 or within the range of 49152 to 65535. Automatically conducting optimum sound tuning (Full Auto MCACC) The Full Auto MCACC Setup measures the acoustic characteristics of your listening area, taking into account ambient noise, speaker connection and speaker size, and tests for both channel delay and channel level. When Measurement Type is Expert, in addition to this, Standing Wave, Reverb chracteristics, Full Band Phase Control and EQ are measured. After you have set up the microphone provided with your system, the receiver uses the information from a series of test tones to optimize the speaker settings and equalization for your particular room. 1 Press u STANDBY/ON to switch on the receiver and your TV. Make sure that the TV's video input is set to this receiver. 2 Connect the microphone to the MCACC SETUP MIC jack on the front panel. ! When connecting the MCACC setup microphone, if "Please wait ..." displays in the main unit display, remove the MCACC setup microphone, then try reconnecting after waiting for approximately one minute. ZONE 2 ON/OFF MULTI-ZONE CONTROL SPEAKERS iPod iPhone DIRECT CONTROL AUTO/ALC/ DIRECT STATUS BAND HDZONE ON/OFF PHASE CONTROL PHONES MCACC SETUP MIC 5V 1 A HDMI 5 INPUT TUNER EDIT Microphone Tripod Make sure there are no obstacles between the speakers and the microphone. If you have a tripod, use it to place the microphone so that it's about ear level at your normal listening position. If you do not have a tripod, use some other object to install the microphone. Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make accurate measurement impossible: ! Sofas or other soft surfaces. ! High places such as tabletops and sofa tops. The Full Auto MCACC display appears once the microphone is connected. 2a.Full Auto MCACC Exit Speaker System : 7.2ch/5.2.2ch EQ Type : SYMMETRY MCACC : M1.MEMORY 1 Dolby Enabled Speaker : NO SP to ceiling : - - - Measurement Type : Expert START Return Important ! Make sure the microphone and speakers are not moved during the Full Auto MCACC Setup. ! Using the Full Auto MCACC Setup will overwrite any existing settings for the MCACC preset you select. ! Before using the Full Auto MCACC Setup, the headphones should be disconnected. ! With factory default settings, the on-screen display will be output from all HDMI output terminals and displayed on any TV connected via HDMI cable. You can change where the screen is output in the MAIN/HDZONE (page 98 ) and HDMI output (page 76 ) settings. CAUTION ! The test tones used in the Full Auto MCACC Setup are output at high volume. ! If you leave the GUI screen for over five minutes, the screen saver will appear. 3 Press MAIN RECEIVER to switch the remote control to the receiver operation mode. 4 Select the parameters you want to set. When the speaker system is not 7.2ch/5.2.2ch, set Speaker System before measuring full auto MCACC. For details, see Speaker system setting on page 94 . ! Speaker System - Shows the current settings. When this is selected and ENTER is pressed, the speaker system selection screen appears. Select the proper speaker system, then press RETURN to return. If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Speaker system setting on page 94 and make sure to connect your speakers as necessary before continuing to step 4. 47