Pioneer SC-91 Owner's Manual - Page 76

09 Using other functions Switching the HDMI output Set which terminal to use when outputting video and audio signals from the HDMI output terminals. The HDMI OUT 1 terminal is compatible with the Control with HDMI function. 1 Press OUT P.. 2 Use i/j to select 'OUT 1/2'. 3 Use k/l to select the output settings for the HDMI OUT 1 and HDMI OUT 2 terminals. Please wait a while when Please wait ... is displayed. The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed. ! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro- nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV's remote control. ! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2 (page 98 ). 4 When you're finished, press RETURN. HDMI 4K/60p signal input setting If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal input setting in accordance with TV performance. Operation is performed on the front panel of the unit. You cannot perform the setting if the multizone function is not set to MULTI ZONE OFF (page 77 ). 1 Switch the receiver into standby. 2 While holding down ENTER on the front panel, press u STANDBY/ON. The display shows RESET c NO d. 3 Select an input terminal that you wish to change settings using i/j. ! 4K/60pBD - Sets the signal for the BD IN terminal. ! 4K/60pH1 - Sets the signal for the HDMI IN 1 terminal. ! 4K/60pH2 - Sets the signal for the HDMI IN 2 terminal. 4 Use k/l to select the signal to set. ! 4:4:4 - Select this setting when connecting to a 4K/60p 4:4:4 24 bit compatible TV using HDMI. More high quality video images can be enjoyed. - When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video image may not be output properly. In that case, select 4:2:0 to watch a 4K/60p 4:2:0 24 bit video image. - When 4:4:4 is set for source equipment that does not support 4K/60p 4:4:4 24 bit, the source equipment's video output may turn red, audio may longer be output from the source equipment, and the equipment may no longer output 3D signals. If this applies to your equipment, change the setting to 4:2:0. ! 4:2:0 - Select this setting when connecting to a 4K/60p 4:2:0 24 bit compatible TV using HDMI. 5 When you're finished, press RETURN. 6 Press u STANDBY/ON to switch on the receiver and your TV. Make sure that the TV's video input is set to this receiver. Changing the channel level while listening Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system. 1 Press CH LV.. 2 Use i/j to select the channel you wish to adjust. 3 Adjust the volume using k/l. The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps. 4 When you're finished, press RETURN. Input Volume Absorber This can be used to correct for the difference in volume between input sources. 1 Switch to the input whose volume you want to adjust. 2 Press CH LV.. 3 Use i/j to select 'ALL'. 4 Adjust the volume using k/l. The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps. 5 When you're finished, press RETURN. 76