Pioneer SC-LX85 Operating Instructions - Page 63
Standby/on. - factory reset
View all Pioneer SC-LX85 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 63 highlights
Using other functions 09 ! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI OUT 1, then select the synchronized amp mode on the TV using the TV's remote control. About the Speaker B Link function When 7.1ch + Speaker B or 5.1ch + SP-B Bi-Amp is selected for the Speaker System setting (page 87) and the Speaker B Link setting (HDMI Setup on page 54) is turned on, the setting of the played speaker terminals switches automatically when HDMI OUT is switched. The settings switch as follows: ! HDMI OUT ALL - Switches to SP: A+B ON. Sound is output simultaneously in the room where the A speakers are located and in the room where the B speakers are located. ! HDMI OUT 1 - Switches to SP: A ON. Sound is only output in the room where the A speakers are located. ! HDMI OUT 2 - Switches to SP: B ON. Sound is only output in the room where the B speakers are located. Checking your system settings Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset. 1 Set the remote control to the receiver operation mode, then press STATUS to check the system settings. The front panel display shows each of the following settings for three seconds each: Input Source d Sampling Frequency d MCACC preset d ZONE 2 input d ZONE 3 input d HDMI OUT. 2 When you're finished, press STATUS again to switch off the display. Resetting the system Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. Set MULTI-ZONE to MULTI ZONE OFF. ! Disconnect the iPod and USB memory device from the receiver beforehand. ! Set the Control with HDMI to OFF (see HDMI Setup on page 54). 1 Switch the receiver into standby. 2 While holding down ENTER on the front panel, press u STANDBY/ON. The display shows RESET c NO d. 3 Select 'RESET' using PRESET k/l, then press ENTER on the front panel. The display shows RESET? OK. 4 Press ENTER to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. ! Note that all settings will be saved, even if the receiver is unplugged. Default system settings Setting Default Digital Video Converter ON SPEAKERS FH/FW Speaker System 9.1ch FH/FW Front SMALL Center SMALL Speaker Setting FH/FW Surr SMALL SMALL SB SMALLx2 SW YES Surround Position IN REAR Crossover 80 Hz X-Curve OFF DIMMER Medium bright Inputs See Input function default and possible settings on page 36. HDMI HDMI Audio Amp HDMI output HDMI OUT ALL Control ON Control Mode ALL Display Power Off YES Audio playback Power On Level LAST Volume Limit OFF Mute Level FULL Phase Control ON Auto Sound Retriever iPod/USB, HOME MEDIA GALLERY, ON ADAPTER PORT input function Other input functions OFF Setting Default Sound Delay 0.0 frame Dual Mono CH1 DRC AUTO SACD Gain 0 dB LFE Attenuate 0 dB Auto delay OFF Digital Safety OFF Effect Level ExtendedStereo 90 Other modes 50 Center Width 3 2 PL II Music Options Dimension 0 Panorama OFF Neo:X Options Center Gain Neo:X CINEMA: 1.0 Neo:X MUSIC: 0.3 Neo:X GAME: 1.0 2 PL IIz Options Height Gain MID All Inputs Listening Mode (2 ch/multi ch) Listening Mode (Headphones) AUTO SURROUND STEREO See also Setting the Audio options on page 57 for other default DSP settings. MCACC MCACC Position Memory M1: MEMORY 1 Channel Level (M1 to M6) 0.0 dB Speaker Distance (M1 to M6) 3.00 m Standing Wave (M1 to M6) ATT of all channels/filters 0.0 dB SWch Wide Trim 0.0 dB EQ Data (M1 to M6) All channels/ bands EQ Wide Trim 0.0 dB 0.0 dB En 63